background image

INSTRUCTIONS FOR USE

 

 11 

87-900-049-01 

(

E

)

 

INSTALLATION 

 

!

 

The controller is equipped with a 3-wire power cord and 
plug (internationally approved) for user's safety. Use 
this power cord and plug in conjunction with a properly 
grounded power socket to avoid electrical shock. 
High voltage developed in the controller can cause 
severe injury or death. Before servicing the unit, 
disconnect the input power cable. 

 

NOTE 

The controller must be installed inside a rack module, 
but it must be positioned so that free air can flow 
through the holes. Do not install or use the controller in 
an environment exposed to atmospheric agents (rain, 
snow, ice), dust, aggressive gases, or in explosive 
environments or those with a high fire risk.  

 
During operation, the following environmental 
conditions must be respected:  
 

• 

temperature: from 0 °C to +45 °C  

• 

relative humidity: 0 - 95%  
(without condensation)  

 
To connect the controller to the pump use the specific 
cable supplied with the controller. 
 
See the section "Technical Information" for detailed 
information about the above mentioned and the other 
connections, and about the options installation. 
 
 

USE 

This paragraph describes the fundamental operating 
procedures. Detailed information and operating 
procedures that involve optional connections or options 
are supplied in the paragraph "USE" of the section 
"Technical Information".  
 
Make all vacuum manifold and electrical connections 
and refer to the pump instruction manual prior to 
operating the controller. 

Controller Controls, Indicators and 
Connectors 

The following paragraph illustrates either the front and 
rear panel with its interconnections.  
 
More details are contained in the appendix "Technical 
Information". 
 
 
 
 

Mini Vac

 

 
 
 

 

1.  High Load LED, comes on when the current absorbed by the 

pump reaches 12 mA 

2.  Output selected polarity LED 
3.  Output voltage scale (KV) 
4.  Main ON/OFF switch 
5.  Voltage/current LED scale 
6.  H.V. LED ON 
7.  Output connector of the sSignal proportional to the current  

1 V= 1 mA log 

8.  Current scale (mA) 

 

Controller Front Panel 

WARNING!

 

2

3

4

6

7

8

Summary of Contents for MiniVac 929-0190





























Reviews: