manualshive.com logo in svg

Vari Lite 20.5002.0004, Service Manual, Page: 91 / 310

Share
Download
Vari Lite 20.5002.0004 Service Manual Download Page 91

C

HAPTER 

3.  M

AINTENANCE 

P

ROCEDURES

3-45

02.9631.0010

CONFIDENTIAL

15 Jan 98

3.3.1.2 

Brightness/Focus Bulkhead Brightness Iris Removal
and Replacement

Parts:

1 EA

ASSY, BRIGHTNESS IRIS (22.1011.0001)

Tools:

Screwdriver, Phillips #1
Screwdriver, Phillips #2
Spacer, 0.05 inch
Nutdriver, 3/16 inch
Nutdriver, 5/16 inch
Loctite 242

To remove and replace brightness/focus bulkhead brightness iris
assembly:

Step 1.

Remove power to luminaire.

Step 2.

Remove head assembly covers.

Step 3.

Remove brightness/focus bulkhead.  Refer to Brightness/Filter
Bulkhead Maintenance paragraph.

Step 4.

Remove focus lens mounting tube from brightness/focus
bulkhead.

a. At linear actuator motor shaft, disconnect focus lens

mounting tube from linear actuator motor.
1. For VL2B luminaire, using 3/16 inch nut driver, remove

2-56 nut and #2 split flat washer from end of shaft
securing focus bearing tube to motor shaft (Figure 3-3).

2. For VL2C luminaire, using 5/16 inch nut driver, remove

4-40 KEPS nut from end of shaft securing focus bearing
tube to motor shaft

Summary of Contents for 20.5002.0004























































































































































































































































































































Reviews:

No comments