manualshive.com logo in svg

Vari Lite 20.5002.0004, Service Manual, Page: 103 / 310

Share
Download
Vari Lite 20.5002.0004 Service Manual Download Page 103

C

HAPTER 

3.  M

AINTENANCE 

P

ROCEDURES

3-57

02.9631.0010

CONFIDENTIAL

15 Jan 98

3.3.2.2 

Gobo/Beam Projector Sensor Removal and
Replacement

Parts:

1 EA

SENSOR, REFLECTIVE OPB700AL (86.7001.0002)

Tools:

Screwdriver, Phillips #1
Screwdriver, Phillips #2
Diagonal cutters
Wrench, 1/4 inch, open end
MTA100 hand crimper

To remove and replace gobo/beam projector sensor:

BRACKET

SENSOR

MOTOR

STEPPER

#4 FLAT WASHER

OF SENSOR

4-40 KEPS NUT

NUMBERED SIDE

GBPSENS

Figure 3-10.  Gobo/Beam Projector Sensor Removal and Replacement

Step 1.

Remove power to luminaire.

Step 2.

Remove head assembly covers.

Step 3.

Remove gobo/beam projector.  Refer to paragraph 3-6.

Step 4.

Remove gobo/beam projector sensor.

a. Remove tie wraps from around sensor wires.

b.   At sensor mount bracket, using 1/4 inch open end wrench,

remove 4-40 KEPS nut and #4 flat washer that secure
sensor to sensor mount bracket and remove sensor.

Summary of Contents for 20.5002.0004























































































































































































































































































































Reviews:

No comments