background image

19 

18 

5. THE 

VOLCANO MEDIC

 HOT AIR GENERATOR

5.4. Commissioning

Do not leave the device unat-

tended while it is being opera-
ted. Put the Hot Air Generator 

on a flat and stable surface. 
Check whether the mains voltage cor-
responds to the voltage rating stated 
on the device. The power cord and 

the plug must be in perfect condition. 
Only connect the Hot Air Generator to 

a properly installed  socket. The man-
ufacturer will not bear any responsibil-

ity whatsoever if this accident preven-
tion measure is not taken.

The device is safely disconnected 

from the mains only when the plug is 
removed from the socket. 
When the power plug is plugged in, 
the LED display of the device lights 
up briefly. At the same time, an inter-
nal software query is performed. The 

green dot on the display shows that 

the Hot Air Generator is connected to 
the power supply.

5.5. Heating Up  

To switch on the heater, push the but-

ton labeled “HEAT”. The set/actual 
temperature will light up, signaling 
that the heater is switched on. At the 
same time, the yellow control lamp 
will light up to indicate that the device 
is heating up. The upper, red display 

shows the actual temperature in the 
Filling Chamber with the air pump 
switched on, and the lower, green 
display shows the desired set tem-
perature. The heating process is com-
pleted when the set value is equal to 
the actual value. Heating up can take 
up to 5 minutes depending upon the 
chosen temperature. After the heating 
process is completed, the tempera-
ture is constantly maintained at the 
set value. The luminous intensity of 
the yellow control lamp corresponds 
to the intensity of the heating process.

For technical reasons the 

temperature in the Filling 
Chamber cannot be meas-

ured during vaporization. During op-
eration the temperature is measured 
at the heat exchanger. The display in-
dicates the reference values for the 
attached Filling Chamber with the air 
pump switched on.

5. THE 

VOLCANO MEDIC

 HOT AIR GENERATOR

5.6. Temperature Setting

Plus temperature 

button

Minus temperature 
button

Actual temperature 
display (red)

Set temperature  

display (green)

When you press the plus button, the 
set value is increased, and when you 
press the minus button, the set value 
is decreased. 
When you briefly tap on the plus or 
minus button, the set values are in-
creased or decreased respectively in 

1-degree increments. 

If you keep the plus or minus button 
pressed, the set values start running 
continuously in the corresponding di-
rection. 
If you simultaneously tap on the plus 
button and the minus button, the dis-
play changes from degree Celsius to 
degree Fahrenheit and vice versa.

If the actual value is higher 

than the set value, you can 
speed up the cooling down 

process by switching on the air pump. 

30 minutes after the last time 

a button is pressed, the devi-
ce automatically switches off.  

As long as the heater has a substan-

tial amount of residual warmth, the 
temperature is displayed until it drops 
below +40°C (+104°F).

Then the display turns off, and the 

green dot on the display indicates that 

the Hot Air Generator is connected to 
the mains supply.

The device is safely discon-

nected from the mains only 
when the plug is removed 

from the socket. 

Summary of Contents for VOLCANO MEDIC

































Reviews: