background image

VLC5501 User manual

6

Starting your vehicle:

Using the keypad PIN code:

To disarm the security system, the correct PIN code must be entered.

To enter the PIN code, proceed as follows:

1.

Turn ON the vehicle’s ignition, the keypad backlight and red LED will illuminate.

2.

Enter your PIN code, the keypad will give a confirmation bleep each time a button is pressed.

3.

Confirm entered PIN code by pushing the

#

button.

4.

If successful the keypad will double beep, the red LED will turn OFF, and the green LED will
turn ON.

5.

The security system is now disarmed – The keypad backlight will go out and the green
conformation LED will remain on.

6.

If the incorrect code has been entered, the keypad will emit one long beep.  In this instance,
switch off the ignition and go back to step 1.

Note:

  Once the keypad has accepted a correct code entry, it will stay in this state and will remain so

until the ignition is switched OFF.

The PIN code must be entered each time the ignition is switched on, except when the ignition has been
switched OFF for less than 4 minutes approx. (read section

passive arming

).

Using the Keypad Override Disc:

In situations where it is not preferable to use the keypad PIN code, it is possible to disarm the security
system using Keypad Override Disc.

1.

With the Keypad Override Disc within a 5 metre range of the vehicle.

2.

Turn ON the ignition and wait until a double beep will sound, the keypad red LED will turn
OFF, and the green LED will turn ON. (This could take up to 20 seconds)

3.

The system is disarmed, now you can start the engine.

Attention!!!  Do not leave the Keypad Override Disc inside the vehicles cabin or
in a 5 metre range, whilst the vehicle is not attended. This device overrides your
security, and should therefore be kept at home in a safe place or on your person
at all times.

Note!!!

The signal from the Keypad Override Disc is transmitted once per 20 seconds. If you

are in an area with a lot of digital transmissions, the communication between disc

and other security system’s components may take longer.

Summary of Contents for VLC5501



















Reviews: