Vapormatic VLC5501 User Manual Download Page 5

VLC5501 User manual

5

1

2

3

4

Keypad Override Disc:

Attention!!!

The Keypad Override Disc is designed as a backup device in the case of a keypad

malfunction or an intruder damaging it trying to start your vehicle.  For this reason

DO NOT

 leave the

vehicle unattended whilst the Keypad Override Disc is within a 5 metre range of the vehicle.  I.E. do
not leave this disc on the vehicle or in, the vehicles cabin whilst it is unattended.

The Keypad Override Disc is a wireless, battery powered identification tag, which informs the security
system about the presence of the operator, this allows the vehicle to start without using the keypad.

Note:

 This disc device operates within a 5 metre range, it transmits a signal every 20 seconds.

Therefore once the ignition is switched on, it may take up to 20 seconds for the Green keypad LED to
illuminate and for the engine to be started.

The Keypad Override Disc consists of following parts:

1.

Enclosure (part1)

2.

Enclosure (part2)

3.

Electronic board

4.

Battery

Replacement battery:

The battery supplied will last for approximately one year, if the Keypad Override Disc stops working
or works intermittently,

please replace the battery first

.

To replace the battery: Separate the enclosures marked 1 & 2, slide the battery out of the unit and
replace with a new fully charged CR2430 (Li-Mn 3V) battery.

Note:

 Please ensure the positive plus sign on the battery matches the positive plus

sign on the battery holder.

With the battery correctly inserted the red LED on the printed circuit board will
flash once.  Carefully place the combined circuit board and battery into enclosure
1, and snap enclosure 2 into place.

Lost or damaged Keypad Override Disc:

If  the  disc  is  lost  or  damaged,  a  replacement  can  be  ordered.    The  security  device  serial  number  is
required as each transponder is uniquely matched to each security system, Vapormatic will then send a
replacement that will only work for the serial number supplied.

Red LED

Summary of Contents for VLC5501



















Reviews: