background image

3.  Meet The VFE-L! 

VFE-L Main Features 

2 hp / 10 Gal Air Compressor

4.5 gpm / 40 psi Water Pump

5 Gal Water Tank

Air/Water Bleeder Hose

Air/Water Blow O

 Valve

Product Description 

The VFE-L is an air compressor and water pump set built into a mobile road case that 
serves as an "Engine" to the VaporFlame System.

 

This case houses an air compressor, water pump, water tank and hoses to deliver 
enough air and water for several VaporFlame units. 

 

Complete with 5 gallon water tank, 

and ultra quiet air compressor, the VFE-L can be located just o

-stage while its hoses 

send air and water to the VaporFlame fixtures. 

 

The VFE-L features a cable door on the 

side for power in, and air/water out. 

 

 

The VFE-L uses a paired valved connector for delivering air and water to the 
VaporFlame e

ect units.  These valved connectors prevent air and water leaks when 

used correctly.   

 

 

Dimensions of the case are 20”w x 15”d x 20”h, and features a tilt-and-roll pull out 
handle. 

 

The VFE opens from the top to access the water tank and the air tank. 

 

 

The VFE-L water tank must be empty for travel/storage, and must be in a “lid-up” 
orientation to run.  The VFE-L case may be run with the lid closed to reduce sound. 

The VFE-L is designed to provide enough air and water to power:

3-4 VF6b Units

1-2 VF8b Unit at 25% Duty Cycle (periodic blast for momentary e

ect- 60-90 

seconds. After which the air tank will need to recharge prior to another blast e

ect. 

Recharge 2-3 minutes)

Page   of 

6

11

Rev. 1.0 4/21

Summary of Contents for VFE-L












Reviews: