background image

4

LUBRICATION

An automatic inline filter-regulator-lubricator is recommended as it increases tool life and keeps the tool in sustained op-

eration. The inline lubricator should be regularly checked and filled with air tool oil. Proper adjustment of the inline lubrica-

tor is performed by placing a sheet of paper next to the exhaust ports and holding the throttle open for approximately 30 

seconds. The lubricator is properly set when a light stain of oil collects on the paper. Excessive amounts of oil should be 

avoided.

In the event that it becomes necessary to store the tool for an extended period of time (overnight, weekend, etc.), it should 

receive a generous amount of lubrication at that time. The tool should be run for approximately 30 seconds to ensure oil 

has been evenly distributed throughout the tool. The tool should be stored in a clean and dry environment.

•  It is most important that the tool be properly lubricated by keeping the inline lubricator filled and correctly 

adjusted. 

Without proper lubrication the tool will not work properly and parts will wear prematurely.

• Use the proper lubricant in the inline lubricator.

 The lubricator should be of low air now or changing air now 

type and should be kept filled to the correct level. Use only recommended lubricants, specially made for pneu-

matic applications. Substitutes may harm the rubber compounds in the tool's O-rings and other rubber parts.

USER-MAINTENANCE INSTRUCTIONS

If a filter/regulator/lubricator is not installed on the air system,

 

air operated tools should be lubricated at least once a day or after 

2 hours work with 2 to 6 drops of oil, depending on the work envi-

ronment, directly through the male fitting in the tool housing. Only 

a qualified technician should perform procedures not specifically 

explained in this manual.

1.  Incorporate an in-line oiler, shut-off valve, regulator 

with pressure gauge, and filter for best service, as 

shown in the diagram at right.

 An inline shutoff valve 

is an important safety device because it controls the air 

supply even if the air hose is ruptured.

Note:

If an automatic oiler system is not used, add a few 

drops of pneumatic tool oil to the airline connection 

before operation. Add a few more drops after each hour 

of continuous use.

2.  Attach an air hose to the compressor's air outlet.

 

Connect the air hose to the air inlet of the tool.

INSTALLATION

1.  Attach a standard 1/4" air connector to the tool's air inlet.

 Wrap the threaded portion of the air connector 

with Teflon tape. Tighten securely.

2.  Attach a standard quick-connector to the air pressure source hose.

 Attach the air hose to the tool.

3.  Set the air pressure regulator on the air compressor to 90 PSI.

 

Do not exceed the recommended pressure of 90 PSI. Excess pressure could result in damage to 

the tool, to your work piece or serious injury.

4.  Check the air line and its connections for air leaks.

 Do not use this tool until you have repaired all air leaks.

Note:

Turn off the air compressor, disconnect the air pressure hose and discharge any residual pressure before 

changing accessories or making any adjustments to the tool. Failure to do so could result in severe injury or 

property damage.

Male

Connector

Quick

Coupler

Quick

Coupler

Valve

Oiler

Filter

Regulator with

Pressure Gauge

Recommended Air Line Components

Tool

Air

Compressor

Male

Connector

Air Hose

on Reel

WARNING

5

DESCRIPTION

Hardened steel barrel and piston for less wear and longer life, lightweight aluminum pistol-grip housing,Front 

exhaust ,150mm air hammer set includes the 4 most popular chisels(round&hex),a retainer spring and a quick 

coupler,190mm air hammer includes 5 chisels(round&hex), a retainer spring and a quick coupler,Ideal for general 

cutting,chipping and scraping.

OPERATION

1. Connect the tool to the air hose.

2. Press the trigger to operate the tool. 

3. The flow of air may be regulated by adjusting flow valve at the base of the handle.

4. Ensure the air supply is clean and does not exceed 90psi while operating the tool. Too high an air pres-

sure and unclean air will shorten the product life due to excessive wear, and may be dangerous caus-

ing damage or personal injury.

DO NOT use any additional force upon the tool.

DO NOT allow tool to free run for an extended period of time as this will shorten its life.

MAINTENANCE

Disconnect tool from air supply before changing accessories, servicing or performing mainte-

nance. Replace or repair damaged parts immediately.

1.  Lubricate the tool daily by dropping a few drops of air tool oil into the air inlet, or use an in-line oiler as 

described on Page 4.

2.  Clean the tool after use.

WARNING

Chisel Opening:

.4" (10mm)

Bore Diameter:

3/4" (19mm)

Blows per minute:

4,500 BPM

Avg. air consumption:

4-8 CFM (800 l/min)

Suggested air pressure:

90 PSI (6.3 bar)

Air inlet size:

1/4"

Air hose:

3/8" I.D.

Suggested air  

compressor:

2 HP

CONTENTS

Air Hammer

Spring Retainer

4 Chisels

TECHNICAL DATA

Summary of Contents for 19709






Reviews: