2
IMPORTANT SAFETY PRECAUTIONS
WARNING! Read and understand all instructions before using this tool. Keep this manual for
the safety warnings and precautions, operating, inspection and maintenance instructions.
When using this tool, basic precautions should always be followed to reduce the risk of per-
sonal injury and/or damage to the equipment.
WORK AREA
1.
Keep your work area clean and well lit.
Cluttered and dark areas invite accidents.
2.
Operate in a safe work environment.
Do not use machines or power tools in damp or wet locations. Do not
expose to rain. Do not use power tools in the presence of flammable gasses or liquids.
3.
Keep children, bystanders and visitors away from the work area.
Do not let them handle tools, hoses or
extension cords. No one should be in the work area if they are not wearing suitable protective equipment.
4.
Store unused equipment.
When not in use, tools must be stored in a dry location to prevent rust. Always lock
up tools and keep them out of reach of children.
PERSONAL SAFETY
1. Use eye, face, head, breathing and ear protection.
Always wear ANSI approved impact safety goggles, which
must provide both frontal and side protection. Wear a full face shield if your work creates metal filings or wood
chips. Wear an ANSI approved dust mask or respirator when working around metal, wood and chemical dusts
and mists. Wear ANSI approved earplugs.
2. Do not over reach; keep proper footing and balance at all times.
Proper footing and balance enables better
control of the tool in unexpected situations.
3. Dress properly, wear protective equipment.
Do not wear loose clothing or jewelry as they can be caught in
moving parts. Tie back long hair. Protective, electrically non-conductive clothes and non-skid footwear are rec-
ommended when working.
4. Stay alert, watch what you are doing and use your common sense.
Do not operate any machine or tool
when you are tired, under the influence of drugs, alcohol or medications.
5. Use clamps or other practical ways to secure and support the work piece to a stable platform.
Holding the
work piece by hand or against your body is unstable and may lead to loss of control.
TOOL USE AND CARE
1. Use the right tool for the job.
Do not attempt to force a small tool or attachment to do the work of a larger
industrial tool. The tool will perform better and safer at the task for which it was intended. Do not modify tools or
use for a purpose for which they are not designed.
2. Maintain tools with care.
Keep tools clean, sharp and in good condition for better and safer performance. Fol-
low instructions for lubrication and changing accessories. Inspect tool fittings, alignment and hoses periodically
and, if damaged, have them repaired by an authorized technician or replaced. The handles must be kept clean,
dry and free from oil and grease at all times. A properly maintained tool reduces the risk of binding and is easier
to control. Do not apply excessive force to try to get the job done faster. Applying excessive force can lead to
slips and damage to your work or personal injury.
3. Avoid unintentional starts.
Be sure that the throttle is in neutral or OFF position when not in use and before
connecting it to any air source. Do not carry the tool with fingers on or near the switch.
4. Only use the lubricants supplied with a tool or specified by the manufacturer.
Other lubricants may not be
suitable and may damage the tool or even make the tool explode.
5. When not in use for an extended period, apply a thin coat of lubricant to the steel parts to avoid rust.
6. Do not use tool if the trigger switch does not function properly.
Any tool that cannot be controlled with the
ON/OFF switch is dangerous and must be repaired.
3
SERVICE
1. Check for damaged parts.
Before using any tool, any part that appears to be damaged should be carefully
checked to determine that it will operate properly and perform its intended functions. Check for alignment and
binding of moving parts, broken parts or mounting fixtures or any other condition that may affect proper opera-
tion. Any part that is damaged should be properly repaired or replaced by qualified technician.
2. When servicing, use only identical replacement parts.
Only use accessories intended for use with this tool.
Replace damaged parts immediately.
AIR SOURCE
1. Disconnect air supply.
Disconnect tools from air pressure source when not in use, before cleaning, servicing or
changing a piece or accessory. After disconnecting, discharge any residual air pressure.
2. Use proper size and type of air pressure line and fittings.
The recommended air line for this tool is 1/4" NPT
air inlet.
3. Always verify prior to using a tool that the air source has been adjusted to the rated air pressure or
within the rated air pressure range.
Over-pressurizing a tool may cause bursting, abnormal operation, break-
age of the tool or serious injury to persons. Use only clean, dry, regulated air at the rated pressure as marked
on the tool.
4. Never use pure oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for a tool.
Such gases are capable of causing an explosion and serious injury to persons. Do not use an air source other
than an air compressor to power this tool.
5. Always use an air regulator and a moisture trap in your compressed air system.
6. Drain the air tank daily.
Water in the air line will damage the tool.
7. Clean air inlet filter weekly.
8. Avoid using an unnecessarily long air hose.
Choose a hose that is appropriate for the situation, as a hose
that is too long and running across the floor can be more dangerous than helpful.
9. Keep hose away from heat, oil and sharp edges.
Check hose for wear, and make certain that all connections
are secure.
10. Always carry a tool by its handle, never carry the tool by the air hose.
11. Line pressure should be increased to compensate for unusually long air hoses over 25 feet.
(8 meters).
The hose diameter should be 3/8” I.D.
VIBRATION PRECAUTIONS
Some tools vibrate during use.
Repeated or long-term exposure to vibration may cause temporary or permanent physi-
cal injury, particularly to the hands, arms and shoulders.
1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor
and then have regular medical checkups to ensure medical problems are not being caused by or wors-
ened from tool use.
Pregnant women or people who have impaired blood circulation to the hands, past hand
injuries, nervous system disorders, diabetes or Raynaud's Disease should not use these tools. If you feel any
medical symptoms related to vibrations (such as tingling, numbness, and white or blue fingers), seek medical
attention as soon as possible.
2. Do not smoke during use.
Nicotine reduces the blood flow to the hands and fingers, increasing the risk of
vibration-related injury.
3. Wear suitable gloves to reduce the vibration effects on the user.
4. Use tools with the lowest amount of vibration when there is a choice between different processes.
5. Do not use for extended periods.
Take frequent breaks when using these tools.
6. Let the tool do the work.
Grip tool as lightly as possible (while still keeping safe control of it.)
7. To reduce vibration, maintain tool as explained in this manual.
If abnormal vibrations occur, stop using this
tool immediately.
