background image

                           

VT-IOT-Dongle   

 

5

21

 

 

1.5

 

Limitation

 

of

 

Liability/Non

warranty

 

For

 

direct

 

or

 

indirect

 

damage

 

to

 

this

 

device

 

or

 

other

 

devices

 

of

 

Vantron

 

caused

 

by

 

failure

 

of

 

conforming

 

to

 

this

 

manual

 

or

 

the

 

safety

 

instructions

 

on

 

device

 

label,

 

Vantron

 

assumes

 

neither

 

warranty

 

nor

 

legal

 

liability

 

even

 

if

 

the

 

device

 

is

 

still

 

under

 

warranty.

 

The

 

VT

IOT

DONGLE

 

should

 

be

 

installed,

 

debugged

 

and

 

maintained

 

by

 

professional

 

people.

   

The

 

outside

 

antennas

 

are

 

not

 

permitted

 

to

 

be

 

installed

 

or

 

to

 

be

 

changed

 

by

 

non

professional

 

people.

 

To

 

run

 

the

 

device

 

normally,

 

only

 

specify

 

antennas

 

are

 

approved

 

to

 

be

 

assembled

 

together

 

by

 

professional

 

people.

 

Unit

 

shall

 

be

 

used

 

with

 

indoor

use

 

antenna

 

only.

 

No

 

antenna

 

for

 

this

 

unit

 

can

 

be

 

installed

 

outdoor.

 

1.6

 

Safety

 

Instructions

 

 

Keep

 

and

 

comply

 

with

 

all

 

operation

 

instructions,

 

warnings,

 

and

 

information.

   

 

Pay

 

attention

 

to

 

warnings

 

on

 

this

 

device.

 

 

Read

 

the

 

following

 

precautions

 

so

 

as

 

to

 

decrease

 

the

 

danger

 

of

 

injury,

 

electric

 

shock,

 

fire,

 

or

 

any

 

damage

 

to

 

the

 

device.

     

 

1.7

 

Precautions

 

 

Pay

 

attention

 

to

 

the

 

product

 

labels/safety

 

instructions

 

printed

 

on

 

silk

 

screens.

 

 

Do

 

not

 

try

 

repairing

 

this

 

product

 

unless

 

declared

 

in

 

this

 

manual.

 

 

Keep

 

away

 

from

 

heat

 

source,

 

such

 

as

 

heater,

 

heat

 

dissipater,

 

or

 

engine

 

casing.

   

 

Do

 

not

 

insert

 

other

 

items

 

into

 

the

 

slot

 

(if

 

any)

 

of

 

this

 

device.

   

 

Keep

 

the

 

ventilation

 

slot

 

ventilated

 

for

 

cooling.

 

•System

 

fault

 

may

 

arise

 

if

 

other

 

items

 

are

 

inserted

 

into

 

this

 

device.

 

 

Installation:

 

ensure

 

correct

 

installation

 

according

 

to

 

instructions

 

from

 

the

 

manufacturer

 

with

 

recommended

 

installation

 

tools.

   

 

Ensure

 

ventilation

 

and

 

smoothness

 

according

 

to

 

relevant

 

ventilation

 

standard.

 

 

 

1.8

 

Safety

 

Instructions

 

for

 

Power

 

Cables

 

and

 

Accessories

 

Proper

 

power

 

source

 

only

 

Start

 

only

 

with

 

power

 

source

 

that

 

satisfies

 

voltage

 

label

 

and

 

the

 

voltage

 

necessary

 

according

 

to

 

this

 

manual.

 

Please

 

contact

 

technical

 

support

 

personnel

 

of

 

Vantron

 

for

 

any

 

uncertainty

 

about

 

the

 

requirements

 

of

 

necessary

 

power

 

source.

   

Use

 

tested

 

power

 

source

   

This

 

product

 

still

 

contains

 

a

 

button

 

lithium

 

battery

 

as

 

a

 

real

time

 

clock

 

after

 

its

 

Summary of Contents for VT-IoT-Dongle






















Reviews: