background image

Owners Manual

SILENT RUNNER INVERTER/CHARGER POWER SYSTEM

4

 

!

"

#

$

"

#

%&

'

(

1

 

Introduction

Thank you for purchasing Vanner’s, Silent Runner (SR) Series Inverter/Charger. We are confident that you will be

satisfied with its performance and its many features. With proper installation and care, you can look forward to years

of service from this high performance product.

This document will describe the operation, technical specifications, installation procedures and accessories offered

for the SR-Series. We suggest that you

 

familiarize yourself with the model numbers of the inverter and optional

accessories you have purchased before proceeding with this manual. If you require additional information please

contact Vanner at 800-227-6937 (800-AC Power) or 614-771-2718.

WARNING: Before you install and use your SR-Series Inverter/Charger

be sure to read and save these safety instructions.

PLEASE NOTE YOUR MODEL AND SERIAL NUMBER HERE FOR FUTURE REFERENCE

Model Number ____________________________ Serial Number _________________________________________

Date of Installation

 ____________________________

Summary of Contents for Silent Runner SRC12-1100PT





























Reviews: