Vanco Evolution EVMX44PRO Manual Download Page 8

Page: 8 / 32

www.vanco1.com

800.626.6445

1. Connect HDMI sources to the HDMI inputs of the EVMX44PRO (NOTE: HDMI certified cables are

strongly recommended for 4K HDR resolution)

2. Connect Cat6 cables from the matrix unit outputs to each display location (NOTE: home run Cat6 cables

are strongly recommended as any coupling points such as punch down RJ45 jacks, female/female RJ45
jacks, etc. can cause signal degradation. Patch panels will cause even more signal degradation.)

3. Connect the HDBaseT Receivers to outputs 1-4, option of either the EVRXHD2 or EVRXDSC; connect

HDMI cables from the receivers to each HDMI display (NOTE: HDMI certified cables are strongly
recommended for 4K HDR resolution)

4. Connect HDMI displays to HDMI outputs 1-4 (NOTE: HDMI certified cables are strongly recommended

for 4K HDR resolution)

5. OPTIONAL: Connect an external amplifier or AV Receiver to the digital and/or analog output(s) (NOTE:

audio source can be extracted from HDMI source inputs or EVRXDSC receiving using ARC function)

6. OPTIONAL: Connect a router or ethernet switch to the TCP/IP RJ45 jack on the EVMX44PRO, this will

connect the matrix unit to the network, and can be controlled via IP

7. Connect the included power cord

CONNECT AND OPERATE

Summary of Contents for Evolution EVMX44PRO

































Search results

Summary of Contents for Evolution EVMX44PRO

Reviews:

Related manuals for Evolution EVMX44PRO

Brands by name

Popular brands

Vanco Evolution EVMX44PRO, Manual

Search results

Summary of Contents for Evolution EVMX44PRO

Reviews:

Related manuals for Evolution EVMX44PRO

Brands by name

Popular brands