Vanco 4x3 HDBaseT Technical Support Download Page 15 | Manualshive

Page: 15 / 20

background image

www.vanco1.com

800-626-6445

15

the Matrix Switcher boasts a USB port for online firmware upgrade on the front panel. Follow these steps to upgrade

firmware:
Step1.

Copy the upgrade software and the latest upgrade file (.bin) to PC.

Step2.

Connect the USB ports of the Matrix Switcher and the PC via USB cable.

Step3.

Double-click the update software icon (see as below).

FIRMWARE UPDATE

It will enter the upgrade interface shown as below:

Step4.

Click Connect USB.

Step5.

Click Open to load the upgrade file, then click Updata to start firmware upgrading.

Note: To ensure available control, the COM number of the PC should be 1~9.

«
...
13
14
15
16
17
...
»

Summary of Contents for 4x3 HDBaseT





















Reviews:

No comments

Related manuals for 4x3 HDBaseT

TNS5500D Series

Brand: 3onedata Pages: 5

IPS7112G-4GS-8GPOE

Brand: 3onedata Pages: 3

Brand: H3C Pages: 55

Brand: H3C Pages: 111

Brand: H3C Pages: 34

Brand: H3C Pages: 47

Brand: H3C Pages: 8

Brand: H3C Pages: 47

Brand: H3C Pages: 4

S5560X-EI Series

Brand: H3C Pages: 63

S5560X-EI Series

Brand: H3C Pages: 89

Brand: H3C Pages: 3

S12500G-AF Series

Brand: H3C Pages: 86

Brand: H3C Pages: 168

Brand: H3C Pages: 56

Brand: H3C Pages: 19

Brand: H3C Pages: 4

Brand: H3C Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands