Vanco 4x3 HDBaseT Technical Support Download Page 14 | Manualshive

Page: 14 / 20

background image

www.vanco1.com

800-626-6445

14

GUI Update

GUI for 4K Home Distribution Hub Kit supports online update in http://192.168.0.178:100. Type the username and

password (the same as the GUI log-in settings, modified password will be available only after rebooting) to log in the

configuration interface. After that, click Administration at the source menu to get to Upload Program as shown below:

Select the desired update file and press Apply, it will start upgrading.

«
...
12
13
14
15
16
...
»

Summary of Contents for 4x3 HDBaseT





















Reviews:

No comments

Related manuals for 4x3 HDBaseT

D DGS-3048 DGS-3048

Brand: D-Link Pages: 3

Brand: Keithley Pages: 434

MMAC-Plus 9H423-26

Brand: Cabletron Systems Pages: 14

Gigabit Switch 8

Brand: 3Com Pages: 2

Brand: I/O Interconnect Pages: 27

Brand: Niles Pages: 7

Brand: Magnum Pages: 3

Cyber SWITCH 1000

Brand: Cabletron Systems Pages: 106

SIL IntelliPoint RF S*R*L Series

Brand: Ametek Pages: 93

TK-407K - KVM Switch - USB

Brand: TRENDnet Pages: 2

Brand: I-Tech Pages: 22

Brand: Kathrein Pages: 41

Brand: Xcellon Pages: 2

DCRS-5200 Series

Brand: Digital China Networks Pages: 4

Brand: SICK Pages: 64

AVS-OP-2416-340

Brand: AMX Pages: 1

Brand: MaxTech Pages: 10

MAGTOP Snap 201

Brand: Bamo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands