background image

www.vanco1.com

 800-626-6445

6

EDID

The EDID switch allows for EDID learning or to pre-set an EDID to encourage a “handshake” between the 
display and source.
The EDID dial helps out in forcing or encouraging a handshake between the source and display with the 
extender in between.  If you are not receiving a video/audio signal with the extender in place, verify the 
category cable isn’t the issue by connecting a pre-terminated jumper or patch cable.  Also verify the source is 
actually sending a signal by connecting straight to the display via HDMI.  
The default EDID setting is set at 0, which should work with most combinations, however if you are 
encountering no HDMI signal, then an adjustment on the EDID dial can be attempted.

Manual EDID Learning Mode

See below for EDID table, when any of the EDID position selections are made, 
the Transmitter will set a fixed EDID to the source.  To make this adjustment, 
follow the below steps while every component is TURNED ON.
1.  Unplug the POWER SUPPLY and HDMI cable from the Transmitting unit only
2.  Adjust the EDID dial to the desired setting
3.  Connect the Power Supply 
4.  Connect the HDMI cable
At this point the EDID you’ve selected is now sent to the source, check the display for video/audio signals.

Auto EDID Learning Mode

Attention: Confirm the extender is displaying audio and video correctly after each selection.  Each time the 
EDID is modified, the transmitter must be unplugged from power and HDMI, and then power plugged back in 
first, followed by the HDMI (see above for manual EDID learning).  

EDID TABLE:

 

POSITION 

EDID DESCRIPTION

 

1080P, 2CH AUDIO

 

1080P, DOLBY/DTS 5.1

 

1080P, HD AUDIO

 

1080I, 2CH AUDIO

 

1080I, DOLBY/DTS 5.1

 

1080I, HD AUDIO

 

3D,1080P, 2CH AUDIO

 

3D, 1080P,DOLBY/DTS 5.1

 

3D,1080P, HD AUDIO

 

1.  Power off all components; unplug power supply to both transmitter and receiver
2.  Unplug HDMI cables connected to transmitter and receiver
3.  Set “EDID” on the transmitting unit 280591-TX at position A to copy EDID of display connected to 

the receiver; Set at position 9 to copy EDID of display connected to the HDMI Loop Out port on the 
transmitter

4.  Connect HDMI Cables
5.  Power on the 280591 Transmitter, followed by the 280591 Receiver
6.  Power on all components from source to display

Summary of Contents for 280591

















Reviews: