-2
Right
Mounting Bracket (
K
)
Left Mounting
Bracket (
J
)
For all Mark Series Brakes
For all Trim-A-Brakes & J-Brakes
For all brakes
Front of
Brake
U
se this diagram as a reference for parts/hardware called out
in these next 2 pages, though each part may only be called
out once in each step. Tools needed: Phillips screwdriver, slot-
ted screwdriver and a 7/16 wrench, or socket wrench.
N
ote: Whether mounting your Trim-A-Gutter™ to a Van Mark brake or mounting on optional UniLegs™ for use with any
brake, knowing beforehand which holes in the mounting brackets apply to your particular Trim-A-Gutter/brake setup will
save you time and effort. Please look over the hole locations above and determine which setup below applies to you before
proceeding.
Setup Note:
Determine the type of Van Mark brake you use and follow the instructions in that column to mount your new tool. For all other brakes you must purchase a set of UniLegs and follow
.
steps 1-6 “Tool Setup on UniLegs” at the bottom half of page 3.
Install &
hook these 2 first
.
MARK SERIES
™
BRAKES
1
As seen in the mounting bracket drawing above, use
holes
O
and
Q
when mounting right bracket
K
and
left
bracket
J
on either side of center casting.
2
Insert hex head screw
C
down front hole
O
of right
bracket
K
. From below, place washer
F
onto threads and
start hex nut
G
. Insert hex head screw
C
down front hole
Q
of right bracket
K
. Again place washer
F
onto threads and
start hex nut
G
. Place bracket
K
over rails letting washers
F
Add these 2 next
to capture brake
rails (see detail C)
3
Insert hex head screw
C
down rear hole of
O
,
w
o
l
e
b
m
o
r
F
.
place washer
F
onto threads and start hex nut
G
. Insert hex
head screw
C
down rear hole
Q
. Again place washer
F
onto
threads and start hex nut
G
should now be captured. Repeat procedure on other side of cen-
ter casting with left bracket
J
then continue to step 4, page 3.
TRIM-A-BRAKE II
™
& J BRAKES
™
1
As seen in the mounting bracket drawing above, use
holes
O
and
P
when mounting right bracket
K
and
left
bracket
J
, on either side of center casting.
2
Insert hex head screw
C
down front hole
O
of right brack-
et
K
. From below, place washer
F
onto threads and start a
hex nut
G
. Lower front of bracket over base rail until washer
F
C
down
rear hole of
O
. From below, place washer
F
onto threads and
start a hex nut
G
to capture front base rail.
3
Position spacer
H
between bracket
K
and rail, align holes.
Insert Hex Hd screws
D
down holes. From below, place
washers
F
onto threads and start hex nuts
G
to capture rail
(see Detail D). Repeat same procedure on opposite side of
center casting with left bracket
J
then continue to step 4,
page 3.
TRIM-A-BRAKE I
™
1
As seen in the mounting bracket drawing above, use
holes
O
and
P
when mounting right bracket
K
and
left
bracket
J
on either side of center casting.
Install & hook
these 2 first!
2
Insert hex head screw
C
down front hole
O
of bracket
K
.
From below, place washer
F
onto threads and start a hex
nut
G
. Insert hex head screw
C
down front hole
P
of right
bracket
K
. Again place washer
F
onto threads and start hex
nut
G
. Place bracket over rails letting washers
F
hook over
Add these 2
next to capture
brake rails
3
Insert hex head screw
C
down rear hole of
O
,
w
o
l
e
b
m
o
r
F
.
place washer
F
onto threads and start hex nut
G
. Insert hex
head screw
C
down rear hole
P
. Again place washer
F
onto
threads and start hex nut
G
should now be captured. Repeat procedure on other side of cen-
ter casting with left bracket
J
then continue to step 4, page 3.
Detail A
Detail C
Detail E
Spacer
Install &
hook these
Center Casting
Center Casting
Center Casting
Detail D
Detail B
Detail B
Long Fast Pin 2 ea.
Short Fast Pin 4 ea.
Hex Head Small
10 ea.
Hex Hd Long
4 ea.
Knob 6 ea.
Washer
8 ea.
Locknut
12 ea.
Spacer
2 ea.
(L)
UniMount
™
Assembly
