background image

www.Valtir.com  

Revision C February 2023

 

Important:

  Read safety instructions thoroughly and follow the assembly 

directions and suggested safe practices before assembling, maintaining, or 

repairing the Triton Barrier

®

 system. Failure to follow this warning can result in 

serious injury or death to workers and/or bystanders. It further compromises the 

acceptance of this system by the FHWA. Please keep these instructions for later 

use. 

 

Warning:

 Ensure that all of the Triton Barrier

®

 system Warnings, Cautions, and 

Important Statements within the Triton Barrier

®

 Manual are completely followed. 

Failure to follow this warning could result in serious injury or death in the event of 

a collision. 

 

Recommended Safety Rules for Assembly 

* Important Safety Instructions * 

This Manual must be kept in a location where it is readily available to persons who are skilled 

and experienced in the assembly, maintenance, or repair of the Triton Barrier

®

  system. 

Additional copies of this Manual are immediately available from Valtir by calling (888) 323-6374. 

This Manual may also be downloaded directly from the websites indicated below. Please 

contact Valtir if you have any questions concerning the information in this Manual or about the 

Triton Barrier

®

 system. 

Always use appropriate safety precautions when operating power equipment, mixing chemicals, 

and when moving heavy equipment or the Triton Barrier

®

 components. Gloves, safety goggles, 

steel toe boots, and back protection should be used. 
Safety measures incorporating traffic control devices specified by the highway authority must be 

used to provide safety for personnel while at the assembly, maintenance, or repair site. 
 

 

Summary of Contents for Triton Barrier TL-2





























Reviews: