background image

www.valtir.com 

13 

Revision F November 2022

 

 

Figure 5 

8)  Placement of inner cones - Energite

®

 III 

Place the appropriate inner cones on the ledge inside the barrel for the 90, 180 and 320 

kg (200, 400 and 700 lb.) modules. (The 640 and 960 kg modules do not require a cone 

insert.) Refer to Page 9 (Figure 1A) of this Manual for a drawing and description of the 

module components. 

Note:

  The same Energite

®

  III cone is used for the 90 and 180 kg (200 and 400 lb.) 

modules. Be sure that all cones are in the proper position (See Figure 6A). 

 

Figure 6A Energite

®

 III System 

9)  Placement of inner cones – Fitch

®

 

For a 200 lb. module place the Unicore on the top shelf (17”); fill to the scribe mark (FILL 

TO HERE FOR 200#) resulting in a 7” sand depth and a 12” void at top. 
For a 400 lb. module place the Unicore on the top shelf (17”); fill to the scribe mark (FILL 

TO HERE FOR 400#) resulting in a 10.5” sand depth and a 8.5” void at top. 
For a 700 lb. module place the Unicore on the second shelf from the top (14”); fill to the 

scribe mark (FILL TO HERE FOR 700#) resulting in a 16” sand depth and a 12” void at 

top. 
For a 1400 lb. module place the Unicore on the third shelf from the top (8.5”); fill to the 

scribe mark (FILL TO HERE FOR 1400#) resulting in a 27.5” sand depth and no void at 

top. 

Summary of Contents for ENERGITE III

























Reviews: