background image

 

       

 

          

     

ADCA

 

                            

 

VAL

S

TEAM

 

ADCA

                     

 

 

 

IMI 9.101 E 02.17 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
CE Marking: 

This product has been designed for use on water, steam, air and other gases which are in Group 2 of 

the European PED-Pressure Equipment Directive in use and it complies with those requirements. 
All the sizes fall within category 2, DN100 pump falling in the category IV and PPA-14 falling in the category III. The 
products carry the CE mark.

 

 

 

 

 

 

 

If malfunction of any other equipment or system operation failure may result in a dangerous overpressure, over 
temperature or even vacuum condition, a safety device must be included in the system to prevent such 
situations. 

Do  not  touch  the  equipment  without  appropriate  protection  during  working  operation  because  it  may  conduct 
heat if the used fluid is at high temperature. 

Before  starting  maintenance  be  sure  that  the  equipment  is  not  pressurized  or  hot.  Even  if  upstream  and 
downstream isolating valves have been closed care should be taken since fluid under pressure may be trapped 
between them. 

The equipments must be used within the working temperature and pressure limits laid down for them, otherwise 
they may fail (refer to nameplate and/or IS- Information Sheet). 

Manual  handling  of  products  may  present  a  risk  of  injury.  You  are  advised  to  assess  the  risks  taking  into 
account the task, the individual, the load and the working environment.  

Before starting work ensure that you have suitable tools and/or consumables available. Use only genuine ADCA 
replacement parts. 

0,80 kg/dm3

5º  Engler

10 bar

0,5 bar

11,2 l

Minimum motive pressure

Pump discharge per cycle DN25 to DN40

APPLICATION LIM ITS POP LC

Minimum density

Maximum viscosity

Maximum motive pressure

0,80 kg/dm3

5º  Engler

10 bar

0,5 bar

16 l

25 l

APLICATION LIM ITS POP-S AND PPO-14

Minimum density

Pump discharge per cycle DN80 x DN50

Maximum viscosity

Maximum motive pressure

Minimum motive pressure

Pump discharge per cycle DN25 to DN50

0,80 kg/dm3

5º  Engler

10 bar

1   bar

325 l

Minimum motive pressure

Pump discharge per cycle DN100 x DN100

APLICATION LIM ITS POP-S DN100

Minimum density

Maximum viscosity

Maximum motive pressure

0,80 kg/dm3

5º  Engler

10 bar

1 bar

21 l

APLICATION LIM ITS PPA-14

Minimum density

Maximum viscosity

Maximum motive pressure

Minimum motive pressure

Pump discharge per cycle DN80 x DN50

Summary of Contents for ADCAMAT POP











Reviews: