background image

7

Getting started

WARNING

Do not attempt to access the card while 

the 

fi

 replace is hot! Let the 

fi

 replace cool 

fi

 rst before touching it!

 First time operation

When operating your new 

fi

 replace for the 

fi

 rst time, 

some  vapors may be released due to the burning of 

curing compounds used during manufacturing. They 

may cause a slight  odor and could cause the 

fl

 ames to 

be the full height of the 

fi

 rebox, or even slightly higher, 

for the 

fi

 rst few hours of operation.

It is also possible that these vapors could set o

  any 

smoke detection alarms in the immediate vicinity. 

These vapors are quite normal on new 

fi

 replaces. We 

recommend opening a window to vent the room. After 

a few hours of use, the vapors will have disappeared 

and the 

fl

 ames will be at their normal height.

Valor safety gas shut-o

 

For your safety, Valor 

fi

 replaces are 

fi

 tted with a 

fl

 ame 

supervision device which will shut-o

  the  gas supply 

if, for any reason, the pilot 

fl

 ame goes out. This device 

incorporates a 

fi

 xed probe, which senses the heat 

from the pilot 

fl

 ame. If the probe is cool, the device 

will prevent any gas 

fl

 ow unless manually lighting the 

pilot. See the full Fireplace and Lighting Information 

card attached to the 

fi

 replace or as reproduced in 

Appendix A of the Installation Manual.

 Locating 

fi

 replace and lighting information

The Fireplace and Lighting Information card is located 

under the 

fi

 rebox.

To access the card, unhook the bottom cover or fret, 

and pull the card out.
There is important information on both sides of the 

card. It must be left with the 

fi

 replace when you are 

done.

739MN

FOR NATURAL GAS    POUR LE GAZ NATUREL

750

24,000

6,500

3.2"

5.0"

4006176N/01

CIRCULATING FAN KIT 755CFK     VENTILATEUR POUR CIRCULATION D'AIR 755CFK

#4003360-741, #4003293-742, #4003313-745, #4003426-765, #4004666 772

   120V, 60Hz, LESS THAN 1A

   120V, 60Hz, MOINS DE 1A

739N 10000

Fireplace 

model
Serial 

number

Summary of Contents for RetroFire RF24DJN



























Reviews: