Valor PORTRAIT 530IN Installation & Owner'S Manual Download Page 39

39

Installation

Install rocks

To get the optimal fl ame 
eff ect, it is important to place 
the rocks in their appropriate 
position. Each rock is 
embossed underneath 
with letters and an arrow 
indicating the position of the 
rock. 

The arrows point to 

the front of the fi replace when the rock is installed

.

See the image and table at the top of the page to help 
you with the identifi cation and position of the rocks.

1.  Identify the rocks 

TFL, TL, TR, and TFR

. These 

rocks have pegs that fi t in the holes on the top of 
the rock base. Install these rocks positioning them 
so that the arrow embossed underneath point to the 
front of the fi replace.

2.  Identify the rocks 

BL, BC, and BR

. These rocks 

have two holes that fi t on the pegs of the ceramic 
platform. Install these rocks positioning them so that 
the arrow embossed underneath point to the front of 
the fi replace.

3.  Identify the rocks 

ML, MC, and MR

. Those rocks 

have pegs that fi ts in the holes on the top of 
the rocks on the front row. Install those rocks 
positioning them so that the arrows underneath 
point to the front of the fi replace.

4.  Identify the rocks 

L and R

. Those rocks don’t have 

any peg or hole. Install those rocks as indicated, at 
the left and right of the rock pile positioning them 
so that the arrows underneath point to the front of 
the fi replace. The rock rests against the other rocks 
and is at an angled position. 

Make sure that the 

TFL rock at the rear left is in the proper angle

—see 

image in step 2. See 
the image at the top of 
the page. You must be 
able to see the edge of 
the platform under the L 
rock (at left) as indicated 
below.

This rock is 

suspended and does 

not rest on the rocks 

of the row behind it.

The edge of the 

platform is visible 

under the rock

Rock 

ID

Description

Other 

markers

Position in the 

fi rebox

TFL

Top far left

1 peg under

Top row rear

TL

Top left

1 peg under

Top row rear

TR

Top right

1 peg under

Top row rear

TRF Top far right

1 peg under

Top row rear

BL

Bottom left

2 holes under, 

1 peg above

Bottom row front

BC

Bottom center

2 holes under, 

1 hole above

Bottom row front

BR

Bottom right

2 holes under, 

1 peg above

Bottom row front

ML

Middle left

1 hole under

Middle row

MC

Middle center

1 peg under

Middle row

MR

Middle right

1 hole under

Middle row

L

Left

Left side

R

Right

Right side

TFL

TFR

TR

BR

R

TL

BL

MR

ML

BC

MC

L

Bottom row front

Middle row

Top row rear

TFL

QUALIFIED 
INSTALLER

Summary of Contents for PORTRAIT 530IN

























































Reviews: