background image

Warranty

WARR

AN

TY

PR

OG

RAM

WARR

AN

TY

PR

OG

RAM

VA

LOR

CO M FO

R

T

VA

LOR

CO M FO

R

T

VA

LOR

CO M FO

R

T

1. Extended Warranty Coverage

For a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at its option pay the initial 
owner for the repair of, or will exchange the following parts or components which are found to be defective in material or workmanship 
under normal conditions of use and service:

2. Two-Year Parts Warranty 

In addition, for two (2) years from the date of purchase, the Company, at its option, can repair or exchange all parts and components 
not listed above but that are found to have a 

bona fi de

 defect in material or workmanship under normal conditions of use.

3. Conditions and Limitations

a)  The warranty registration card must be completed by the initial owner and returned to the Company within 90 days of purchase. 

Alternatively, the warranty registration form may be 

fi

 lled out online at www.valor

fi

 replaces.com.

b)  Installation and maintenance must be performed by an authorized and trained dealer in accordance with the Company’s installation 

instructions.

c)  This warranty is void where installation of the unit does not conform to all applicable codes including national and local gas 

appliance installation codes and building and 

fi

 re codes.

d)  The owner must comply with all operating instructions.
e)  The Company is not responsible for the labor costs to remove defective parts or re-install repaired or replacement parts.
f)  The initial owner of the unit will be responsible for any shipping charges for replacement parts as well as travel time incurred by the 

dealer to perform the warranty work.

g)  This warranty applies to non-commercial use and service and is void if it is apparent that there is abuse, misuse, alteration, 

improper installation, accident or lack of maintenance to the unit.

h)  This warranty does not cover damage to the unit due to:

i) 

Improper installation, operational or environmental conditions.

ii) 

Inadequate ventilation in the area or competition for air from other household equipment or appliances.

iii)  Chemicals, dampness, condensation, or sulphur in the fuel supply lines which exceeds industry standards.

i)  This warranty does not cover glass, log breakage or damage to the unit while in transit.
j)  The Company does not allow anyone to extend, alter or modify this warranty and assumes no responsibility for direct, indirect or 

consequential damages caused by the unit. State or provincial laws where the 

fi

 rst purchaser or user resides may provide speci

fi

 c 

rights to extend this warranty and, if so, the Company’s sole obligation under this warranty is to provide labor and/or materials in 
accordance with those laws.

4. Discharge of Liability

After two (2) years from the date of purchase, the Company may, at its option, fully discharge all obligations under this warranty by 
paying to the 

fi

 rst owner the wholesale price of any defective parts.

5. No Other Warranty

All obligations to repair this unit are de

fi

 ned in this warranty. Some states or provinces may speci

fi

 cally mandate additional warranties 

on the part of manufacturers, but in the absence of such speci

fi

 c legislation, there is no other warranty or obligation expressed or 

implied.

Part or Component

Defect Covered

Maximum Warranty Period

Exterior steel casing

Corrosion

10 years

Glass

Loss of structural integrity

10 years

Cast iron parts

Corrosion

10 years

Firebox and heat exchanger

Corrosion (but not discoloration) causing 
loss of structural integrity

10 years

If you have a problem with this unit, please contact your dealer or 
supplier immediately. Under no circumstances should you attempt 
to service the unit in any way by yourself. The warranties in para-
graphs 1 and 2 are provided only to the initial owner of this unit, 
are not transferable and are subject to the conditions and limita-
tions in paragraphs 3, 4 and 5. Please review the conditions and 
limitations carefully and strictly follow their requirements.

40

OWNER’S 
INFORMATION

Summary of Contents for LEGEND G3 739JN















































Reviews: