Valor 722AP Installation And Owner'S Manual Download Page 1

Model 722AN - for Natural Gas

Model 722AP - for Propane Gas

GAS FIREPLACE

  

With 

ADORN 

or 

VISAGE 

Fire Front

This appliance is a domestic room heating appliance. It must not be used for any other purpose
such as drying clothes etc.

600A727/09

INSTALLATION

 AND OWNER’S

MANUAL

Please read this manual before
installing and operating.

-

 

Do not store or use gasoline or other flammable  vapors
and liquids in the vicinity of this or any other appliance.

-

 

WHAT TO DO IF YOU SMELL GAS

 

Do not try to light any appliance

 

Do not touch any electrical switch

 

Do not use any phone in your building.

 

Immediately call your gas supplier from a neighbor’s
phone. Follow the gas suppliers instructions.

 

If you cannot reach your gas supplier, call the fire
department.

- Installation and service must be performed by a qualified
installer, service agency or the gas supplier

WARNING: If the
information in these
instructions is not followed
exactly, a fire or explosion
may result causing property
damage, personal injury or
death.

f i r e - p a r t s . c o m

Summary of Contents for 722AP





















Reviews: