background image

7

© Vallox Oy - All rights reserved

1.4  

Outdoor air compensation menu (NTC 2 Temp)

The outdoor air compensation function (NTC 2 installed) 

can be used to control the fan speed as a function of the 

outdoor temperature. When the outdoor temperature 

drops below the temperature set for starting the 

outdoor air compensation function, the fan starts 

to decrease the fan speed linearly by the specified 

percentage, until the end temperature for outdoor air 

compensation is reached. The fan speed is restricted 

by a specified percentage when the outdoor air 

compensation end temperature is reached.

Use the + button to proceed to the outdoor air 

compensation menu. 

Use the Menu button to proceed to the setting mode. 

Use the +/– buttons to set the outdoor air temperature 

compensation function to On or Off. Press Menu to 

confirm the setting. Outdoor air compensation requires 

installing the NTC 2 sensor (outdoors). Selecting Off 

takes you back to the Main menu.

If you select On, the Compensation Start menu opens. 

Use the Menu button to proceed to the setting mode. 

Use the +/– buttons to set the start temperature (+10...–

10°C). Press Menu to confirm the setting.

Use the + button to proceed to the Compensation Stop 

menu. Use the Menu button to proceed to the setting 

mode. Use the +/– buttons to set the end temperature 

for compensation (–10...–30°C). The compensation is 

applied linearly between the start and end temperature. 

Press Menu to confirm the setting.

Use the + button to proceed to the maximum 

temperature drop menu for the compensation function 

(Temp Drop). Use the Menu button to proceed to the 

setting mode. Use the +/– buttons to set the maximum 

Temp Drop as a percentage. Press Menu to confirm the 

setting.

Use the + button to proceed to the return menu.  

Use the Menu button to return to the Main menu. If the 

status is active, there is a dot in the bottom right corner 

of the display.

MANU

AL

+/

Menu

Menu

Menu

+/

Menu

Menu

+/

Menu

+/

Menu

+

Summary of Contents for Exxeo





















Reviews: