background image

4

used, the minimum extract air chamber pressure = Ext L 

is active and the maximum extract air chamber pressure 

= Ext H is active. 
The Constant Flow function maintains a extract air flow 

(only in the pressure transmitter model Vallox Exxeo 

DPC). You can choose two limit values for the extract 

air flow. The Low value specifies the minimum air flow 

and the High value specifies the maximum air flow. If 

analog control is used (0–10 VDC), the minimum air 

flow equals 0 VDC and the maximum air flow equals 10 

VDC. If digital control is used, the minimum air flow = Ext 

L is active and the maximum air flow = Ext H is active. 

Using the air flow temperature compensation function 

requires installing the NTC 1 temperature sensor. The 

temperature measurement NTC 1 is used to correct the 

change due to the density of air in the air flow. The K 

value is a model-specific value of the Vallox Exxeo roof 

fan. An incorrect K value results in an incorrect air flow 

measurement result.

1.2  

Constant Flow menu

Press the Menu button to open the Constant Pressure 

menu.

Use the Menu button to proceed to the setting mode. 

Use the +/– buttons to select On or Off. Press Menu to 

confirm the setting. Selecting Off takes you back to the 

Constant Pressure menu.

If you select On, the Pressure Low  

Setpoint menu for the extract air chamber opens in the 

display. Use the Menu button to proceed to the setting 

mode. Use the +/– buttons to set the desired value 

(0–2,500 Pa). The minimum pressure cannot be higher 

than the maximum pressure. Press Menu to confirm the 

setting.

Use the + button to exit to the Pressure High Setpoint 

menu for the extract air chamber.  Use the Menu button 

to proceed to the setting mode. Use the +/– buttons 

to set the desired value (0–2,500 Pa). The maximum 

pressure cannot be lower than the minimum pressure. 

Press Menu to confirm the setting. 

Use the + button to proceed to the return menu.

Use the Menu button to return to the Main menu. If the 

status is active, there is a dot in the bottom right corner 

of the display.

MANU

AL

+/

Menu

Menu

+/

+/

+

Menu

+/

Menu

Menu

Menu

Menu

Summary of Contents for Exxeo





















Reviews: