background image

7

© Vallox Oy - All rights reserved

MOUNTING ON THE WALL

NOTE

Avoid mounting the unit on a hollow, echoing partition wall or 

on a bedroom wall, or prevent the conduction of sound.
The minimum distance between the top of the unit and the 

finished ceiling surface is 30 mm. Note that during mounting the 

unit rises 10 mm higher than the final height.

Mount the ventilation unit on the wall with a mounting plate, as shown 

in the adjacent figure. Make sure that the unit is horizontally level after 

mounting.

MOUNTING ON THE CEILING

Vallox 101 MV can be equipped with an optional ceiling mount plate. 

To attach the ceiling mounting plate:

•  On rafter frames or other frame structure with M8 thread bars so 

that they withstand the weight of the unit.

•  Ensure that the installation plate is horizontally level, as this 

determines the position of the unit.

•  The top edge of the white covering strip of the ceiling mounting 

plate can be installed against the ceiling. Alternatively, a concealed 

mounting method can be used, in which case the ceiling can be 

30 mm below the top of the white covering strip. 

Insulate the ducts against condensation also between the unit and the 

ceiling mounting plate.

Mounting the ceiling mounting plate

1.  Fasten the thread bars on the rafter frames or other frame 

structure, and screw the nuts (E) onto the bars.

2.  Lift the ceiling mounting plate in place.

3.  Push a rubber damper (F) and a washer (G) to each thread bar.

4.  Adjust the nuts so that the ceiling mounting plate is level.

5.  Shorten the lower ends of the thread bars so that they are no more 

than 5 mm below the nuts. 

CAUTION

The ventilation unit is very heavy. Do not perform this 

procedure alone.

 INSTALLATION

INS
TALLA
TION

1

2

NOTE

When installing the unit, 

reserve a space of at 

least 555 mm in front 

of the unit for servicing 

purposes.

Summary of Contents for A3741

























Reviews: