background image

20

TECHNIC

AL SPECIFIC

ATIONS

1

1

3

5

6

7

2

8

10

9

13

14

15

17

16

18

19

20

21

11

12

4

22

23
24
25

26

27

NO. PART

CODE

NO. PART

CODE

NO. PART

CODE

1.

Supply / extract air fan 935450

11. 

HR cell bypass damper 

assembly

4102523

21.

RJ45 extension cable

952197

2.

Supply air fan 

attenuation grid

935451

12.

Damper motor

930621

22. Connection box

3526700

3.

Wall mounting plate

3080700

13.

Post-heating resistor

942220

23. MyVallox Control panel

949033

4.

Siphon Vallox Silent 

Klick

3494701

14.

Door

4102334

24. MyVallox humidity sensor

(optional)

946149

5.

Coarse and fine filter 

for supply air

978225

15.

Mounting screw of the 

door

990712

25.

MyVallox carbon dioxide 

sensor

(optional)

949111

6.

HR cell

933260

16.

Motherboard

949032-1

26. MyVallox VOC sensor

(optional)

949112

7. 

Lower support for HR 

cell

4102504

17.

Safety switch

948370

27.

Supply air filter frame

4108194

8. 

Upper support for HR 

cell

3467200

18.

Glass tube fuse 63mA 

slow 5x20mm

952490

9. 

Filter frame (extraction) 978226

19.

NTC sensor kit

7033900

10. 

Coarse filter for extract 

air

978227

20.

Internal humidity and 

carbon dioxide sensor

4107982

EXPLODED VIEW AND PARTS LIST

Summary of Contents for A3741

























Reviews: