3
Inhibit Option (Meet Me Answer)
The V-2006A/V-2006AHF is equipped with an inhibit
feature that automatically mutes output to the speakers
and allows a handset conversation between the paging
party and a single line telephone connected to the
paging Tip and Ring. A single line telephone modified
for "A" Lead Control and a 5.1K Ohm 1/4 Watt resistor
is required to use the inhibit
function.
NOTE: If the inhibit option has been connected to a
single line phone and that phone goes off hook
during a page, the speakers will mute.
Inhibit does not affect the override feature.
Warble and Single Tones
Warble tone is activated when a common audible
contact closure or 90VAC ring voltage is supplied by the
telephone system to UNA closure or UNA ring input. A
single tone may be activated by an additional contact
closure to the clock tone input.
Group Call
Each group can be programmed with any combination
of zones. Zone may be included in multiple groups.
Dial codes for group call are 7, 8 and 9. Group calls are
one-way only.
All Call Group
Each zone, 1 through 6, can be programmed for all call
(group 0). When "0" is dialed, all zones activate
including group 0 of any expansion unit.
Page Port Access
Page Port requires a 600 Ohm page port
that will pass
DTMF for zone selection and is equipped with a
separate "page enable" contact closure.
Additionally, the page port must be capable of passing
bi-directional audio if talkback is used.
Expansion Unit
Up to ten V-2006A/V-2006AHF units can be
connected together to provide a system wide all call.
Modular RJ11 plugs J7 and J9 are provided for this
expansion setup.
INSTALLATION
NOTE: The telephone system referred to in this
document is the customer premise equipment such
as a key system or PABX. The V-2006A/V-2006AHF
CANNOT be connected directly to the public
telephone network (a central office line). All
connections must be made prior to plugging the
unit to AC power.
Mounting
The V-2006A/V-2006AHF was designed for wall or
table mounting. Secure unit to wall studs or suitable
brace away from heat sources or strong
magnetic
fields (motors, fans, power supplies, etc.) with
control and terminal strip accessible. Four wood
screws are included for mounting.
NOTE: All controls and terminations are accessed
by removing the small right side panel. To remove
panel, loosen the two screws holding the panel in
place and lift panel away from the board.
SWITCH SELECTABLE OPTIONS
Refer to Figure 2.
Loop/Ground Start Access
If the V-2006A/V-2006AHF is being used with
Loop/Ground Start Access, set SW6 to Up (ON). SW2
selects loop or ground start access from the telephone
system. SW1 selects loop or ground start access for
the override feature.
NOTE: When using a ground start trunk port, a
ground strap must be used to connect GND of the
V-2006A or V-2006AHF to an appropriate telephone
system ground (see Figure 1).
Page Port Access
If the V-2006A/V-2006AHF is being used with a page
port, set SW6 Battery Feed to OFF (down position).
Page port must:
1. Provide dry page enable contact closure
2. Pass DTMF tones for zone selection
3. Pass audio in both directions when used with
V-2006AHF for handsfree talkback
Dial Tone, Alert Tone/Ringback Tone
There are four (4) dip-switches for setting options also
located on the board (see Figure 2 also).
SW3 Dip
Switch
Options
Off (UP)
(away from
Board)
ON (DOWN)
(toward
Board)
4
Not Used
Not Used
3*
Repeated Alert
Tone
No Repeated
Alert Tone
2*
Alert Tone/
Ringback Tone
No Alert Tone
1
Dial Tone
No Dial Tone
NOTE: * Alert Tone and Repeated Alert Tone are
available only on V-2006AHF handsfree outputs.
Telephone System Access Connections
A 66 block with 50-pin female amphenol connector is
required. See Figure 1 for 66 block pinouts. Tip and
ring connections can be made to the RJ11 (J4) with a
modular cord or punched down on the W/BL pair on the
block.
Page Port Connections
Make certain Battery Feed switch is OFF. SW6 should
be in Down position. Connect Tip, Ring
of Page Port
to W/BL, BL/W. Connect wiring from telephone
system’s dry contact closure to W/BR
and O/W of
the 66 block.
