background image

Page 9 

Valcom 12” & 16”  Wireless Clock Installation Manual 

(Rev 1.02)

 

Valcom  5614 Hollins Road    Roanoke, VA 24019    Phone: (540) 563-2000

   

Fax: (540) 362-9800   www.valcom.com

 

Valcom  5614 Hollins Road    Roanoke, VA 24019    Phone: (540) 563-2000

   

Fax: (540) 362-9800   www.valcom.com

 

Overview 
 
The number of times that the switch is pressed will determine the diagnostic mode. After 
determining the diagnostic mode, the LED between the two (2) switches will start flash-
ing a green light. The number of flashes will display the diagnostic number.  
 
DIAGNOSTIC #1 
This diagnostic will determine how long (# of hours) since the clock last received the 
communication signal.  
In order to enter diagnostic one (1) mode, push the Diagnostic Switch once which is indi-
cated by the green LED flashing one (1) time with a one (1) second break. 

 

A.  While in diagnostic modes, hour and minute hands continue to run normally. 
B.  The second hand will display how long since the clock received time signal (please 

see below table for details) 

C.  After three (3) minutes, the clock will resume normal operation. 

Second Hand Position 

Time Since Clock Last Received a Communication Signal 

12 

Clock has received communication within the past hour 

        “              “                “                between one and two hours ago 

        “              “                “                between two and three hours ago 

        “              “                “                between three and four hours ago 

        “              “                “                between four and five hours ago 

        “              “                “                between five and six hours ago 

        “              “                “                between six and seven hours ago 

        “              “                “                between seven and eight hours ago 

        “              “                “                between eight and nine hours ago 

        “              “                “                between nine and ten hours ago 

10 

        “              “                “                between ten and eleven hours ago 

11 

        “              “                “                more than eleven hours ago 

Diagnostic Testing 

Summary of Contents for 12"













Reviews: