background image

Chapter 1 _________________________________________________________ General Information 

VAISALA_________________________________________________________________________ 9 

Warranty 

Vaisala hereby represents and warrants all Products 
manufactured by Vaisala and sold hereunder to be 
free from defects in workmanship or material 
during a period of twelve (12) months from the date 
of delivery save for products for which a special 
warranty is given. If any Product proves however to 
be defective in workmanship or material within the 
period herein provided Vaisala undertakes to the 
exclusion of any other remedy to repair or at its 
own option replace the defective Product or part 
thereof free of charge and otherwise on the same 
conditions as for the original Product or part 
without extension to original warranty time. 
Defective parts replaced in accordance with this 
clause shall be placed at the disposal of Vaisala. 

Vaisala also warrants the quality of all repair and 
service works performed by its employees to 
products sold by it. In case the repair or service 
works should appear inadequate or faulty and 
should this cause malfunction or nonfunction of the 
product to which the service was performed Vaisala 
shall at its free option either repair or have repaired 
or replace the product in question. The working 
hours used by employees of Vaisala for such repair 
or replacement shall be free of charge to the client. 
This service warranty shall be valid for a period of 
six (6) months from the date the service measures 
were completed. 

This warranty is however subject to following 
conditions: 

a)  A substantiated written claim as to any alleged 

defects shall have been received by Vaisala 
within thirty (30) days after the defect or fault 
became known or occurred, and 

b)  The allegedly defective Product or part shall, 

should Vaisala so require, be sent to the works 
of Vaisala or to such other place as Vaisala may 
indicate in writing, freight and insurance 
prepaid and properly packed and labelled, 
unless Vaisala agrees to inspect and repair the 
Product or replace it on site. 

This warranty does not however apply when the 
defect has been caused through 

a)  normal wear and tear or accident; 

b)  misuse or other unsuitable or unauthorized use 

of the Product or negligence or error in storing, 
maintaining or in handling the Product or any 
equipment thereof; 

c) wrong installation or assembly or failure to 

service the Product or otherwise follow 
Vaisala's service instructions including any 
repairs or installation or assembly or service 
made by unauthorized personnel not approved 
by Vaisala or replacements with parts not 
manufactured or supplied by Vaisala; 

d)  modifications or changes of the Product as well 

as any adding to it without Vaisala's prior 
authorization; 

e)  other factors depending on the Customer or a 

third party. 

Notwithstanding the aforesaid Vaisala's liability 
under this clause shall not apply to any defects 
arising out of materials, designs or instructions 
provided by the Customer. 

This warranty is expressly in lieu of and excludes 
all other conditions, warranties and liabilities, 
express or implied, whether under law, statute or 
otherwise, including without limitation any implied 
warranties of merchantability or fitness for a 

 

particular purpose and all other obligations and 
liabilities of Vaisala or its representatives with 
respect to any defect or deficiency applicable to or 
resulting directly or indirectly from the Products 
supplied hereunder, which obligations and 
liabilities are hereby expressly cancelled and 
waived. Vaisala's liability shall under no 
circumstances exceed the invoice price of any 
Product for which a warranty claim is made, nor 
shall Vaisala in any circumstances be liable for lost 
profits or other consequential loss whether direct or 
indirect or for special damages. 

 

Summary of Contents for Drycap DMT142



















































Reviews: