background image

6

Operating instructions ecoTEC pro 0020209590_03

3.3

Displayed symbols

Symbol

Meaning

Explanation

Burner operating cor-
rectly

Burner on

bar

Current filling pressure of
the heating system
The dashed lines show
the permitted range

Permanently on:
Filling pressure in
the permitted range

Flashing: Filling
pressure outside
the permitted range

Hot water generation
active

Permanently on:
Draw-off mode be-
fore burner is on

Flashing: Burner on
in draw-off mode

Heating mode active

Permanently on:
Heating mode heat
requirement

Flashing: Burner on
in heating mode

Comfort mode active

Permanently on:
Comfort mode active

Flashing: Comfort
mode active, burner
on

Maintenance required

Information on the main-
tenance message in the
"Live Monitor"

Summer mode active
Heating mode is
switched off

Burner anti-cycling time
is active

To avoid the need for
frequent switching on
and off (increases the
product's working life).

F.XX

Fault in the product

Appears instead of the
basic display, may be
an explanatory plain text
display.

3.4

Information on the identification plate

The identification plate is mounted on the underside of the
product in the factory.

Information on the
identification plate

Meaning

Read the instructions.

VUW…

Vaillant gas-fired wall-hung boiler for
heating and hot water generation

..6/5-3

Calorific value power/product generation
equipment

ecoTEC pro

Product description

2H, G20

20 mbar

(2.0 kPa)

Gas group and gas connection pressure
as set at the factory

ww/yyyy

Date of manufacture: Week/year

Cat.

Permissible gas categories

Types

Approved gas-fired units

PMS

Permissible total overpressure in heating
mode

PMW

Permissible total overpressure during hot
water generation

T

max.

Max. flow temperature

Information on the
identification plate

Meaning

ED 92/42

Current efficiency directive fulfilled with
4* rating

V Hz

Mains voltage and mains frequency

W

Max. electrical power consumption

IP

Level of protection

Heating mode

Hot water generation

P

Nominal heat output range

Q

Heat input range

D

Nominal hot water draw-off rate

Bar code with serial number,
7th to 16th digit = product article number

3.5

Serial number

The serial number is located on a plastic plate at the bottom
of the front casing.

3.6

CE marking

The CE marking shows that the products comply with the
basic requirements of the applicable directives as stated on
the declaration of conformity.

The declaration of conformity can be viewed at the manufac-
turer's site.

3.7

Energy Saving Trust Endorsed Products

Only the most energy efficient products can carry the
‘Energy Saving Trust Endorsed Product’ brandmark making
it easy for consumers to choose products that have met strict
energy performance criteria.

Available for: Boilers, Heating controls and chemical inhib-
itors, the Energy Saving Trust endorsed product brandmark
gives consumers confidence that a product will cost less to
run, help lower energy bills and reduce carbon emissions.

About the Energy Saving Trust

Energy Saving Trust is an independent and impartial organ-
isation that provides trusted energy saving advice to em-
power millions of people to lead affordable, low energy life-
styles. For more information visit energysavingtrust.org.uk

Summary of Contents for ecoTEC pro 30 H combi A VUW 306/5-3

















Reviews: