Vaillant ecoFIT pure Installation And Maintenance Instructions Manual Download

Page: 32 / 52

Appendix

Installation and maintenance instructions ecoFIT pure 0020230533_01

Status code

Meaning

S.16

DHW mode: Fan overrun

S.17

DHW mode: Pump overrun

Display in Comfort mode with warm start or hot water handling mode with cylinder

S.20

Hot water handling mode: Requirement

S.21

Hot water handling mode: Advance fan operation

S.22

Hot water handling mode: Pump pre-run

S.23

Hot water handling mode: Burner ignition

S.24

DHW mode: Burner on

S.25

DHW mode: Pump/fan overrun

S.26

DHW mode: Fan overrun

S.27

DHW mode: Pump overrun

S.28

Hot water handling mode: Temporary shutdown of the burner

Other displays

S.30

Room thermostat is blocking heating mode.

S.31

No heating demand: Summer mode, eBUS controller, waiting period

S.32

Fan waiting time: Fan speed outside of the tolerance values

S.33

Forced fan operation until the pressure monitor is switched

S.34

Frost protection active

S.39

Underfloor heating contact open

S.41

Water pressure too high

S.42

Flue non-return flap closed

S.46

Frost protection mode (Comfort): Minimum load

S.53

Product in waiting period/operation block function due to low water pressure (flow/return spread too large)

S.54

Waiting period: Low water pressure in the circuit (flow/return spread too large)

S.76

Maintenance message: Check the water pressure

S.88

Product purging active

S.91

Maintenance: Demo mode

S.96

Automatic test programme: Return temperature sensor, heating demands blocked.

S.97

Automatic test programme: Water pressure sensor, heating demands blocked.

S.98

Automatic test programme: Return temperature sensor, heating demands blocked.

S.99

Internal automatic test programmes

S.108

Purging the combustion chamber, fan in operation

S.109

Product's standby mode activated

Overview of fault codes

Note

Since the code table is used for various products, some codes may not be visible for the product in question.

Fault code

Meaning

Possible cause

F.00

Fault: Flow temperature sensor

NTC plug not plugged in or has come loose, multiple plug on the PCB not
plugged in correctly, interruption in cable harness, NTC sensor defective

F.01

Fault: Return temperature sensor

NTC plug not plugged in or has come loose, multiple plug on the PCB not
plugged in correctly, interruption in cable harness, NTC sensor defective

F.10

Short circuit: Flow temperature sensor

NTC sensor defective, short circuit in the cable harness, cable/casing

F.11

Short circuit: Return temperature sensor

NTC sensor defective, short circuit in the cable harness, cable/casing

F.12

and

F.91

Short circuit: Cylinder temperature
sensor

NTC sensor defective, short circuit in the cable harness, cable/casing

F.13

Short circuit: Domestic hot water cylinder
temperature sensor

NTC sensor defective, short circuit in the cable harness, cable/casing

Summary of Contents for ecoFIT pure





















































Search results

Summary of Contents for ecoFIT pure

Reviews:

Related manuals for ecoFIT pure

Brands by name

Popular brands

Vaillant ecoFIT pure, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for ecoFIT pure

Reviews:

Related manuals for ecoFIT pure

Brands by name

Popular brands