Vaillant auroTHERM plus VFK 155 H Installation Manual Download

Page: 33 / 52

Flat roof fitting and installation 5

0020100571_03 auroTHERM, auroTHERM plus Installation manual

Vertical collector position

Installation angle 60°

Weights/rack [kg]

To secure against sliding and

lifting

To secure only against lifting

(if secured/anchored against

sliding)

Note

When there are at least two collectors in a row, the ballast loads can be re-
duced by half for the outer rack.

Basic wind speed [km/h]

Position

Building height

up to 10

10-18 m

18-25 m

up to 10

10-18 m

18-25 m

up to 90

Inland

₁

₂

460
424

568
529

641
599

280

348

393

up to 90

Coast and islands

₁

₂

604
564

713
669

785
739

370

438

483

up to 99

Inland

₁

₂

568
529

677
634

785
739

348

415

483

up to 99

Coast and islands

₁

₂

749
704

857
809

930
879

461

528

573

up to 108

Inland

₁

₂

677
634

821
774

930
879

415

506

573

up to 108

Coast and islands

₁

₂

893
844

1002

949

1110
1054

551

619

105
686

5.1.8

Defining the rack clearances

▶

Define the rack clearances.

Number of collectors

[mm]

30°

45°

60°

[mm]

Vertical

970

1280

2927

1731

3666

2065

4019

2034

−

2200

1100

−

3463

1263

4726

5989

7252

8515

Dimension applies to 20° position of the sun and must be checked according to the geographical location.

Summary of Contents for auroTHERM plus VFK 155 H





















































Search results

Summary of Contents for auroTHERM plus VFK 155 H

Reviews:

Related manuals for auroTHERM plus VFK 155 H

Brands by name

Popular brands

Vaillant auroTHERM plus VFK 155 H, Installation Manual

Search results

Summary of Contents for auroTHERM plus VFK 155 H

Reviews:

Related manuals for auroTHERM plus VFK 155 H

Brands by name

Popular brands