Vaderstad Seed Hawk Manual Download Page 27 | Manualshive

Page: 27 / 34

background image

Fans

Remove covers and check couplings. Inspect sensor for visible defects.

Fill systems

Inspect fill system arm assembly. Grease should be added to the 6 bushings in the arm
assembly before and after every season. Refer to your operators manual to keep augers/
conveyors in good condition. Follow maintenance procedures as described in the manual.
Ensure you have properly cleaned out the system at the end of the season.

Check the Power Skid

Thoroughly examine charging system. Inspect and adjust belt if equipped. Blow out the
alternator with compressed air. Grease zerk found on underside of alternator. Ensure you
reattach the ground wire on the back when reinstalling the alternator cover.

Battery

Load test the battery, confirm adequate CC/CCA is present. Remove and store battery in a
heated, controlled environment during off season storage.

Lubricate

Consult the operator’s manual to locate all grease points and maintenance instructions for
the your air cart.

Fenix III

Ensure meter housing is completely cleaned out when switching rollers, or during post
season maintenance. Rollers should be washed and stored in a cool, dark temperature
controlled environment. Lubricate motor shafts before reinstalling.

Re-tighten wheel bolts and check tire pressure

Consult your operator’s manual for proper torque specs and tire pressures.

Safety!

Carefully read the safety instructions in the instruction manual before any service or
maintenance work is carried out. Inspect and follow all safety decal instructions at all
times.

7

8

9

10

11

Winter storage tips

Properly maintaining and storing your equipment will save you time and money. After
completing your post season maintenance, prepare your equipment for winter storage by
following the above tips and consulting our QuickStart videos available on our website.

During post season clean up/maintenance, run floor dry through your fill system and each
section to absorb any excess moisture. Ensure tank lids are closed but unsealed to protect
against damage caused by fluctuating temperatures.

Rollers (cleaned and washed), battery, and all electronics (iPads, fill system remotes,
switchbox) should be stored in a cool, dark, temperature controlled environment.

Good to

know!

12

13

View QuickStart video

«
...
25
26
27
28
29
...
»

Summary of Contents for Seed Hawk



































Reviews:

No comments

Related manuals for Seed Hawk

Brand: GYS Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands