manualshive.com logo in svg

VADA VFB-S75, Installation Manual

Share
Download
VADA VFB-S75 Installation Manual Download Page 8

8

VADA FLOW BOSS 

SUBMERSIBLE PUMP

 

VFB-S75 

INSTALLATION MANUAL

FLOW BOSS

25mm FI Outlet

25mm FI Mains Inlet

Brass end cap 
DN25 nut

25mm FI Inlet

UV Stabilised ABS plastic 
casing for longevity

Dual Check Valve

Brass tail

KNOW YOUR PRODUCT 

VFB-MSU25

SPECIFICATIONS 

VFB-MSU25

The Vada Flow Boss Mechanical Water Switching Unit VFB-MSU25 is a fully automatic mechanical 
unit that switches between tank and mains water. This device is designed for pressure pump supply 
systems, and allows you to harvest rainwater for the toilet, laundry, and other household applications 
with automatic mains backup. 

The 25mm Switching Unit is suitable for up to 3 toilets, a washing machine, and an additional tap 
outlet including irrigation.

The Vada Flow Boss Mechanical Switch is suitable for clean water only.

•  Pump inlet: 25mm FI 
•  Mains water in: 25mm FI 
•  Outlet: 25mm FI 
•  Max mains pressure: 1000kPa / 10 bar 
•  Min pump pressure: 350kPa / 3.5 bar 
•  Max flow rate: 100 litres per minute 
•  Max water temp: 50°C

Summary of Contents for VFB-S75

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands