Vacon X5EIP01 Installation Manual Download Page 16

Page: 16 / 20

EIP

Ethernet IP with

115

VAC / Encoder Interface Option Board

vacon

Ethernet Troubleshooting

Following are the advanced fault codes for the drive fault (F38) related to the option board. For more information,
see the X5 User’s Manual (Chapter 8). The

option board status LEDs

are described on

page 9

of this manual.

Table 9: Advanced Fault Codes

Advanced

Fault Code

Fault

Possible Cause

Corrective Measures

Option board loss

Option board is disconnected or
damaged

Check option board status LEDs,
ribbon cable connection, and
cycle power. Replace option
board if necessary.

Unstable ID during power-up

Option board hardware issues

Cycle power. If problem persists,
contact Vacon technical support.

Option board changed

Option board was changed during
last power-down

If the change was intentional,
cycle power.

Invalid ID

Option board hardware issues

Cycle power. If problem persists,
contact Vacon technical support.

Wrong or no daughter card
installed

Option DIMM module issues

Cycle power. If problem persists,
contact Vacon technical support.

Option board software error

Option board software issues

Cycle power. If problem persists,
contact Vacon technical support.

Option board removed

Option board was removed during
last power-down sequence

If the change was intentional,
cycle power. Otherwise, follow
corrective measures for fault
code 1.

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for X5EIP01





















Search results

Summary of Contents for X5EIP01

Reviews:

Related manuals for X5EIP01

Brands by name

Popular brands

Vacon X5EIP01, Installation Manual

Search results

Summary of Contents for X5EIP01

Reviews:

Related manuals for X5EIP01

Brands by name

Popular brands