background image

Care and maintenance

5.1 

Cleaning the housing

Take care that no water gets into the housing of the appliance! If wa-
ter gets into the housing, it can cause damage.

Do not use abrasive cleaners, scouring pads, steel wool, etc. for
cleaning, as they can damage the surface. Remove the screw fuse or
switch off the circuit breaker.

Cleaning the outside/inside

▸ Clean the outside using a slightly damp cloth – and detergent if necessary

– and wipe dry.

Grease and condensate water can build up on the inside next to the metal
grease filters.
▸ Clean using a slightly damp cloth – and detergent if necessary – and wipe

dry.

5.2 

Cleaning the grease filters

The grease filters must be cleaned at least once a month with normal use or
whenever the   button flashes. If cleaned monthly, the service life of the
grease filters is as long as that of the range hood.

The saturation indicator becomes visible when the appliance is in op-
eration or a power level is activated.

5.3 

Removing the grease filters

▸ Pull the glass de-

flector plate com-
pletely out and
switch the appliance
off.

▸ Fold the grip 

2

 on

the grease filter 

1

forward.

▸ Carefully pull the

grease filter down
and out of its holder.

1

2

18

Summary of Contents for DFPQ

































Reviews: