V.ORLANDI RP10 Installation, Operating And Maintenance Instructions For The Installer And The User Download Page 17 | Manualshive

Page: 17 / 36

V.ORLANDI RP10 Installation, Operating And Maintenance Instructions For The Installer And The User Download Page 17

REV. 00

PAG.

17/36

CAUTION: inspect to see that the coupling-up procedure has been
conducted correctly; check that the operating handle (19c) has
regularly returned back
into position.

CAUTION: in the event that the operating handle (19c) is not back in
position, try moving the tractor unit forwards for about 50 cm and
then back again so that the semi-trailer king pin is repositioned
correctly to
enable regular coupling.

If the operating handle (19c) will still not turn back into position
regularly,
or if the semi-trailer counter plate does not completely rest on the fifth
wheel surface, vehicle travel is strictly prohibited, no matter what.

Contact the nearest service workshop for necessary intervention.

Wind the semi-trailer landing legs fully up to stroke end.

6)

FIFTH WHEEL Rp10

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS

CHAP. 3

«
...
15
16
17
18
19
...
»

Summary of Contents for RP10





































Reviews:

No comments