Assembly
ASSEMBLY ACCESSORIES
PART No.
DESCRIPTION
QTY
Rubber Weight Bumper
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
30
Rubber Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
66
Crown Plate Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
67
Crown Plate Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
68
Crown Plate Collar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
76
06
Square Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
100
101 M10 x 75mm Hex Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
102 M10 Flat Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
103 M10 Nylon Locknut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
M10 x 65mm Hex Bolt . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Part
NO
.10
1
Part NO.102
Part NO.103
Part NO.76
Part NO.30
Part NO.66
Part NO.6
Part
NO
.10
0
Part NO.68
Carefully unpack each component, checking against the parts list that
you have all the necessary parts to complete the assembly of your
product.
Please note that some of the parts may be pre-fitted to major
components, so please check carefully before contacting our
CUSTOMER SUPPORT team.
In any event, please do not return the product to your retailer before
contacting us first.
Tel:- 0800 3 101 202 or
+44 (0) 1535 637711
Email:- [email protected]
CUSTOMER SUPPORT open from 9.00am to 5.00pm
from Monday to Friday
Part
NO
.67
Do NOT FULLY TIGHTEN any
Bolts, Nuts or Fittings at this
stage unless specifically
instructed to do so.
Note
INSTRUCTIONS:- STAGE A
TOOLS REQUIRED
1 x Soft Headed Hammer - 1 x Adjustable Spanner - 1 x 13mm (1/2'') Spanner - 1 x 14mm (9/16'') Spanner
ASSEMBLY OF THIS GYM WILL BE EASIER WITH 2 PEOPLE
Securely attach the Front Frame Stabiliser (2) to the front end of the Main Floor Frame (1) using 2 x
M10 x 75mm Hex Bolts (101), 4 x M10 Flat Washers (102) and 2 x M10 Nylon Locknuts (103).
Lay the Rear Upright (12) on top of the Rear Frame Stabiliser (3) making sure the longest part of the bottom
bracket is facing the weight guide tubes and secure in place using 2 x M10 x 75mm Hex Bolts (101), 4 x M10
Flat Washers (102) and 2 x M10 Nylon Locknuts (103).
Attach the Rear Frame Stabiliser (3) to the Main Floor Frame (1) by lifting the Main Floor Frame (1) over the Rear
Frame and secure in place using 2 x M10 x 75mm Hex Bolts (101), 4 x M10 Flat Washers (102) and 2 x M10 Nylon
Locknuts (103).
Cap both Frame Stabilisers (2 and 3) and the central Main Floor Frame Support (1) with 6 x Rubber Caps (30)
and 1 x Square Cap (76) securing in place using a small amount of household adhesive if desired.
Loosely attach the Front Upright (4) to the Main Frame (1) from the side with 2 x M10 x 75mm Hex
Bolts (101), 4 x M10 Flat Washers (102) and 2 x M10 Nylon Locknuts (103).
Slide the 2 x Rubber Weight Bumpers (6) onto the bottom of each Weight Guide Tube (7). Pass both Weight
Guide Tubes (7) into the holes in the central Main Floor Frame Support (1), and secure in place with 2 x M10 x
65mm Hex Bolts (100), 4 x M10 Flat Washers (102) and 2 x M10 Nylon Locknuts (103), then lay all the large
Weight Plates (8) making sure they are the correct way round with the center edge slot at the bottom of each
weight. Ensure the hole 3/4 of the way down the Guide Tube (7) is positioned at the bottom when installing the
Guide Tubes(7) into the Main Floor Frame Support (1).
Slide the 10 hole Weight Selector Tube (11) into the central hole in the weight stack. Place the Crown
Weight Collar (68) over the top of the Weight Selector Tube (11). Line up the top hole of the Weight Selector
Tube (11) with the hole in the Crown Weight Collar (68) and slide in the Crown Weight Pin (67) so that it is
loosely attached. Finally, lay the Crown Weight (9) over the top of the Weight Selector Tube (11) so the Crown
Weight Collar (68) fits into the recess on the underside of the Crown Weight (9) and lay the Crown Weight
Washer (66) on top of the Crown Weight (9).
1
2
3
4
5
6
7
Beny Sports Co. UK Ltd.
Unit 8 Riparian Way,
The Crossings Business Park,
Cross Hills,
West Yorkshire.
BD20 7BW
Page 16
Summary of Contents for STG/09-2
Page 1: ...CH2921 STG 09 2 HERCULEAN COMPACT ADDER HOME GYM...
Page 2: ......
Page 13: ...Exercise Notes Page 13...
