V-Bro Products Garage Gator GGR125 Installation And Operation Instructions Manual Download Page 5

Page: 5 / 17

Carefully inspect your new motorized storage unit for any possible damage and/or

shortage of parts. Separate all major components and parts as detailed below and on

the next page. Do not attempt installation if parts are damaged or missing. If parts of your

GGR125 are missing or appear damaged call V-Bro customer service at 1-888-GATOR-

08, Monday - Friday, 8:00 AM to 5:00 PM Eastern Time. Before calling carefully check the

carton as parts may be in the packing material.

CARTON INVENTORY

Garage Gator Motorized Storage Unit

(A) Motor Mounting Plate

MAJOR COMPONENTS

(B) Motor Hoist

(C) Spacer Channel Bar

(D) Spacer Channel Pulley Bar

IMPORTANT NOTE

The motor mounting plate (A)

and motor hoist (B) are bolted

together when shipped.

IT IS

NECESSARY

to remove the

motor hoist from the motor

mounting plate by

loosening

(it

is not necessary to remove) the

nuts from the fixed, threaded

bolts on the motor mounting

plate. Once loosened, the motor

hoist can easily be slid off the

motor mounting plate.

(H) Hooks x4

(I) Bike Cables x2

(J) Bonus Storage Net

(X) 100lb Capacity Platform

Summary of Contents for Garage Gator GGR125


















Search results

Summary of Contents for Garage Gator GGR125

Reviews:

Related manuals for Garage Gator GGR125

Brands by name

Popular brands

V-Bro Products Garage Gator GGR125, Installation And Operation Instructions Manual

Search results

Summary of Contents for Garage Gator GGR125

Reviews:

Related manuals for Garage Gator GGR125

Brands by name

Popular brands