V-Bro Products Garage Gator GGR125 Installation And Operation Instructions Manual Download Page 15

Page: 15 / 17

CONTACT INFORMATION

Garage Gator Motorized Storage Unit

MAINTENANCE

Garage Gator Motorized Storage Unit

V-Bro Products is on call. Installation and service information as well as ordering repair parts

is as near as your telephone Monday - Friday 8:00 AM to 5:00 PM Eastern Time (subject to

holidays). Contact us toll free.

1. Check to be sure the motor is properly attached to its mounting plate. Make sure

the bolts are tight.

2. Periodically check the condition of the electrical cords, plugs and controls.

3. Periodically check cables for slippage or excessive wear.

SPECIFICATIONS

Garage Gator Motorized Storage Unit

Model

--------------------------------- GGR2436PS

Load Capacity

----------------------------- 100 lbs

Lifting Height

------------------------- 117 inches

Lifting Speed

---------------------------- 33ft/min

Cable Length

------------------------- 165 inches

Cable Diameter

-------------------------- 1/8 inch

Voltage

----------------- 120V / 60 HZ 4.5 Amps

Motor

--------------------------------------- 3/4 HP

V-Bro Products

28114 County Road 561

Tavares, Florida 32778

888-GATOR-08

fax: 352-742-0702

email: [email protected]

1-888-GATOR-08

Summary of Contents for Garage Gator GGR125


















Search results

Summary of Contents for Garage Gator GGR125

Reviews:

Related manuals for Garage Gator GGR125

Brands by name

Popular brands

V-Bro Products Garage Gator GGR125, Installation And Operation Instructions Manual

Search results

Summary of Contents for Garage Gator GGR125

Reviews:

Related manuals for Garage Gator GGR125

Brands by name

Popular brands