UWT Capanivo CN 4000 Series Technical Information/Instruction Manual Download Page 20

Page: 20 / 21

Level limit switch

Series CN 4000

Technical Information / Instruction manual

page

Notes for use in Hazardous Locations

Zone classification

General Notes

Marking

Devices with Ex approval are marked on the name plate.

Process pressure

The device construction allows process over-pressure upto 6/ 16 bar (87/ 232 psi) (see name

plate). These pressures are allowed for test purposes. The definition of the ATEX/ IEC-Ex is only

valid for a container-over-pressure between -0.2 .. +0.1 bar (-2.9 .. +1.45 psi). For higher or lower
pressures the approval is not valid.

Process and ambient

temperature

The permitted temperature ranges are marked on the name plate. Observe derating curves.

Permitted zones (categories) for mounting in partition wall

EPL (IEC-Ex)

Category (ATEX)

Zone

EPL (IEC-Ex)

Category (ATEX)

Zone

Max. Surface Temperature

The temperature marking on the name plate refers to the instruction manual. On the following tables the relevant
temperature ratings are shown. The maximum surface temperature is the hottest temperature of the unit which could occur during

malfunction (according to Ex-definition).

Max.

ambient

temperature*

Max. process
temperature*

Max. surface

temperature

60°C (140°F)

CN 4020: 120°C (248°F)
CN 4030: 110°C (230°F)

120°C (248°F)

CN 4050: 80°C (176°F) 135°C (275°F)

Version CN 4020 120°C/ CN 4030/ CN 4050:

Usable in

zone

ATEX

category

IEC-Ex

Equipement Protection

Level (EPL)

Dust applications 20, 21, 22

1 D

* in case of conductive dust
additional demands for the
installation are possible.

21, 22

2 D

3 D*

Ambient

Process

Max.

ambient

temperature

Max. process

temperature

Max. surface

temperature

60°C (140°F)

120°C (248°F)
130°C (266°F)
140°C (284°F)
150°C (302°F)
160°C (320°F)
170°C (338°F)
180°C (356°F)

Version CN 4020 180°C:

* Observe derating (see page 7)

Capanivo

CN 4000

gi011217

Summary of Contents for Capanivo CN 4000 Series






















Search results

Summary of Contents for Capanivo CN 4000 Series

Reviews:

Related manuals for Capanivo CN 4000 Series

Brands by name

Popular brands

UWT Capanivo CN 4000 Series, Technical Information/Instruction Manual

Search results

Summary of Contents for Capanivo CN 4000 Series

Reviews:

Related manuals for Capanivo CN 4000 Series

Brands by name

Popular brands