Operating and Maintenance
Your UV system is on continuously during normal use.
After periods of not using your water supply exceeding 2-3 days, it is
recommended to open all faucets and flush your plumbing lines for a
minute or two.
Caution
: Protect your unit from freezing. Drain all water from the unit
if freezing temperatures exist.
Ultraviolet lamp replacement-
The ultraviolet lamp located inside the
chamber will operate effectively, round the clock, for approximately
one year. The lamp will light longer than that. However, the UV light
penetration may fall below the prescribed safety level. Therefore,
annual lamp replacement is necessary regardless of apparent
condition.
Replacing the UV lamp and cleaning the quartz
sleeve
Note:
Do not touch the lamp or the quartz sleeve with your fingers.
Handle by ends only or wear soft gloves.
n
Unplug the system from the electrical outlet and turn off all water
supplies to the unit.
o
Carefully extract the lamp connector from the sleeve gland nut
assembly to just expose the top of the lamp. While holding the lamp
base firmly, remove the lamp power connector.
Caution:
lamp base
can be very hot – be careful not to drop lamp into quartz sleeve as it
easily broken.
p
Carefully slide the UV lamp out of the quartz sleeve and discard.
q
Remove the quartz sleeve by loosing the glandnut and carefully
extracting from unit.
Caution:
The quartz sleeve is fragile and is easily
chipped or broken – use care when removing or installing.
r
Clean the quartz sleeve with a vinegar solution or a readily
available scale removal product (
Limeaway, CLR etc.
)
s
Re-install the quartz sleeve – replace “O” ring if it appears
damaged.
t
Install new lamp by reversing procedure described in step 2 above.
u
Slowly open water supply valve and purge air from system – verify
that there are no leaks before reconnecting to AC power.
RESETTING THE LAMP CHANGE TIMER
n
The lamp change reminder timer is reset by disconnecting the UV
power source from the AC supply, waiting for fifteen seconds and
reconnecting to the AC supply with the timer button depressed. The
UV power source will emit a solid three-second beep indicating that
the reset was successful.
It is not possible to reset the lamp change timer unless the timer
is in the grace or lamp change alarm mode. If you need to reset
the lamp change reminder timer prior to the full one-year time
period expiring due to premature lamp failure, there are special
instructions included with all replacement lamps describing the
necessary procedure.
Product Specification
UVD400E
Rated Flow Rate
10 gpm
(38lpm)
(2.3m
3
/hr)
AC Supply Voltage
120V 47-63Hz .7A
(240V 47-63Hz .35A)
Annual Lamp Change Timer
yes
Lamp Change Grace Period
28 days maximum
Grace Period Audio Alarm Disable
yes (7day increments)
Reactor Chamber Material
304 SS
Maximum Operating Pressure
100psi
Maximum Ambient Temperature
50C (122F)
Water Temperature Range
4 – 37C (40 – 99F)
Lamp Service Life
9000hrs
Chamber Dimensions (L x D)
23” x 3.5”
Controller Dimensions (L x D x W)
7” x 1.7” x 2.3”
Shipping Weight
8lbs
Inlet/Outlet Port Size
3/4” MNPT inlet
3/4”MNPT outlet
Warranty
UV Dynamics water disinfection systems are supported with a ‘free from
defects’
Workmanship and Material
warranty as follows:
-A ten-year pro-rated warranty on the stainless steel disinfection chamber
-A one-year warranty on UV lamps, sleeves and sensor
-A three year warranty on the UV power source
-Warranty commences from date of purchase. Proof of purchase required
UV Dynamics will repair or replace, at its option, any defective parts covered by
the warranty. Shipping and handling are not included in this warranty. They will be
collected from you by your Dealer. Replacement parts provided under warranty will
be sent to your UV Dynamics dealer.
Parts repaired or replaced under the pro-rated warranty will be covered under
warranty to the end of the original warranty period. This warranty is also subject to
the conditions and limitations outlined under the heading “General Conditions and
Limitations” below.
Warranty for Replacement Lamps and Parts
UV Dynamics warrants replacement lamps, purchased for annual routine
maintenance and other parts purchased to repair product components that are no
longer covered by the original warranty, to be free from defects in material and
workmanship for a period of three (3) months from the date of purchase. During this
time, UV Dynamics will repair, or replace at its option, a defective replacement lamp
or part free of charge except for shipping and handling charges. The warranty
period on replacement lamps and parts will be verified using date codes and/or
purchase receipts. Your UV Dynamics Dealer will advise you on whether the
defective item needs to be returned to UV Dynamics for failure analysis.
General Conditions and Limitations
None of the above warranties cover damage caused by improper use or
maintenance, accidents, acts of God or minor scratches or imperfections that do not
materially impair the operation of the product. The warranties also do not cover
products that are not installed as outlined in the applicable Owner’s manual.
These limited warranties outline the exclusive remedy for all claims based on a
failure or defect in any of these products. They are in lieu of all other warranties
whether written, oral or implied or statutory.
Under no circumstance shall UV Dynamics have any liability for liquidated
damages for collateral, consequential or special damages or for loss of profits, or for
actual losses or for loss of production or progress of construction, regardless of the
cause of such damages or losses. In any event, UV Dynamics aggregate total
liability shall not exceed the specific product purchase price. The purchaser agrees
to indemnify and hold harmless UV Dynamics from all claims by third parties in
excess of these limitations.
UV Dynamics does not assume any liability for personal injury or property
damage caused by the use or misuse of any of its products. UV Dynamics shall not
in any event be liable for special, incidental, indirect or consequential damages. UV
Dynamics liability shall, in all instances, be limited to replacement of the defective
product or part and this liability will terminate upon expiration of the applicable
warranty period.
REPLACEMENT PARTS
UV Lamp 400128
Quartz Sleeve 400129
“O” Ring Set 400202
UV Power Source 400255
© COPYRIGHT 2011
y
UVDynamics Inc.
y
All RIGHTS RESERVED
