background image

13

above  grade.  Termination  of  the  vent  shall  be 

not  less  than  7  feet  above  an  adjacent  public 

walkway. The vent terminal shall not be installed 

closer than 3 feet from the inside corner of an L 

shaped structure. Termination of the vent should 

be  kept  at  least  3  feet  away  from  vegetation. 

The  venting  system  shall  terminate  at  least  4 

feet horizontally from, and in no case above or 

below  electric  meters,  gas  meters,  regulators, 

and relief equipment.

If multiple terminations are used, there must be 

a  minimum  of  12  inches  between  the  exhaust 

of one termination and the air intake of the next 

termination. See Figures 1-3 in Section E5 for il-

lustrations.

NOTE:

 All field installed vent pipe must be 3”.

INSTALLATION

1. Attach  combustion  air  intake  piping  to  sup-

plied Fernco 2” coupling on CVI gas valve. At-

tach vent piping to furnished 2” CPVC  vent tee 

on draft inducer outlet.

NOTE:

 All pipe joints are to be water tight.

2.  Working  from  the  boiler  to  the  outside,  cut 

pipe to required length(s).

3. Deburr inside and outside of pipe. Remove all 

chips and shavings.

4. Chamfer outside edge of pipe for better distri-

bution of primer and cement.

5. Clean and dry all surfaces to be joined.

6. Check dry fit of pipe and mark insertion depth 

on pipe.

NOTE:

 It is recommended that all pipes be cut, prepared, and 

pre-assembled before permanently cementing any joint.

7.  After  pipes  have  been  cut  and  pre-assem-

bled, apply cement primer to pipe fitting socket 

and end of pipe to insertion mark. Quickly apply 

approved cement to end of pipe and fitting sock-

et (over primer). Apply cement in light, uniform 

coat on the inside of socket to prevent buildup of 

excess cement. Apply second coat.

8. While cement is still wet, insert pipe into sock-

et with a ¼ turn twist. Be sure pipe is fully in-

serted into fitting socket.

9. Wipe excess cement from joint. A continuous 

bead of cement will be visible around perimeter 

of a properly made joint.

10. Handle pipe joint carefully until cement sets.

11. Support combustion air and vent piping a mini-

mum of every 5 feet using pre-formed metal hang-

ing straps. Do not rigidly support pipes.  Allow for 

movement due to expansion and contraction. 

NOTE:

 Rigid supports will cause excess noise in vent piping.

12. Slope combustion air and vent pipes toward 

boiler a minimum of ¼” per linear foot with no 

sags between hangers.

13.  Use  appropriate  methods  to  seal  open-

ings where vent and combustion air pipes pass 

through roof or side wall.

IX. GAS SUPPLY PIPING

CHECK GAS SUPPLY

The gas pipe to your boiler must be the correct size 

for the length of run and for the total BTU per hour 

input of all gas utilization equipment connected to 

it. See Table 6 for proper size. Be sure your gas 

TABLE 5 - GAS SUPPLY PRESSURE

Pressure

Natural Gas Propane Gas

Minimum

4” w.c.

10” w.c.

Maximum

10” w.c.

14” w.c.

Please check line pressure while unit is running.

line  complies  with  local  codes  and  gas  company 

requirements.

The boiler and its individual shutoff valve must be 

disconnected  from  the  gas  supply  piping  system 

during any pressure testing of that system at test 

pressures in excess of  ½ psig (3.5kPa).

The boiler must be isolated from the gas supply pip-

ing system by closing its individual manual shutoff 

valve during any pressure testing of the gas supply 

piping system at test pressures equal to or greater 

than ½ psig (3.5kPa).

Summary of Contents for UB90 125









































Reviews: