UTICA BOILERS MACF-115 Manual Download

Page: 60 / 139

10.5 Frost Protection

Boiler monitors supply and return water temperatures to

enable frost protection which automatically turns boiler

and pump on.

If water in boiler falls below 41°F (5°C), providing boiler

is connected to power, boiler will operate until water

temperature in the system reaches approximately 86°F

(30°C).

Frost protection is for boiler only and not for complete

Central Heating System.

10.6 Pump

If electricity is connected to the boiler, regardless if

power is "On" or "Off" and has not operated for 24

hours for heating or hot water, boiler pump will operate

automatically for one minute every 24 hours.

10.7 Low Water Pressure Sensor (Internal)

This device protects primary exchanger from damage.

It will not allow boiler to run in a LOW water pressure

situation. Low water condition occurs when water

pressure drops below 7.0 psi (0.5 bar).

10 - OPERATING INSTRUCTIONS

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands