UTICA BOILERS MACF-115 Manual Download

Page: 41 / 139

7 - GAS SUPPLY PIPING

7.2 Gas Pipe Recommendations

Configure gas pipe for proper operation and avoid issues

with failure to light or maintenance of proper flame

during operation, which could cause error codes related

to flame signal.

•

Incoming pipe size and pressures shall be sufficient

for all gas appliances in the building. See Chart next

page or reference NFPA-54.

•

Use only properly rated and certified materials for

gas pipe.

• Use of Schedule 40 metallic pipe and Corrugated

Stainless-Steel Tubing (CSST) is manufacturer

recommended for best performance.

•

Use of Gas Appliance Connectors (flexible connectors

typically used for gas stoves or water heaters) is

prohibited. Refer to national and local building codes.

•

Each fitting in the gas supply pipe shall count as 5

equivalent feet.

•

There shall be sufficient gas pressure at the boiler per

gas used and appliance rating plate.

• For LP applications there shall be no less than 10

linear feet of properly sized gas pipe excluding

fittings from the closest regulator or meter in the gas

supply piping.

ACCEPTABLE PIPING FOR

PROPANE

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands