UTICA BOILERS MAC-115 Manual Download Page 11 | Manualshive

Page: 11 / 139

UTICA BOILERS MAC-115 Manual Download Page 11

7

Check our website frequently for updates: www.ecrinternational.com

Information and specifications outlined in this manual in effect at the

time of printing of this manual. ECR International reserves the right to

discontinue, change specifications or system design at any time without

notice and without incurring any obligation, whatsoever.

2 - INTRODUCTION

2.5 Designated Use

• MAC-115

,

MAC-150

and

MAC-205

provide both

central heating and domestic hot water.

• MAH-100, MAH-125

and

MAH-165

central heating

only.

• Indoor installation.
• Closet or alcove installation. Direct Vent Boiler does not

require air vents when installed in closet or room.

• Direct vent boiler.
•

For use with natural gas or liquefied petroleum gases

(LP/propane).

2 - Introduction

2.1

Installation shall conform to requirements of authority

having jurisdiction or in absence of such requirements:

UNITED STATES

• National Fuel Gas Code, ANSI Z223.1/NFPA 54

.

• National Electrical Code, NFPA 70.

2.2

Where required by authority having jurisdiction,

installation shall conform to Standard for Controls and Safety

Devices for Automatically Fired Boilers, ANSI/ASME CSD-1.

Additional manual reset low water cutoff may be required.

2.3 Requirements for Commonwealth of

Massachusetts:

Boiler installation must conform to Commonwealth of

Massachusetts code 248 CMR which includes but is not limited

to:

Installation by licensed plumber or gas fitter.

2.6 The unit MUST NOT:

• Directly heat potable water. Indirect heating is

acceptable.

• Heat water with non-hydronic heating system chemicals

present (example, swimming pool water).

• Toxic chemicals, such as those used for boiler

treatment, shall not be introduced into potable water

used for space heating.

• Exceed 43 psig (2.96 bar) maximum system pressure,

or drop below minimum system pressure 7.25 psig (.50

bar)

• Exceed 176°F (80°C) system design temperature.

2.7

Operational Features

• MAH-100

Modulates input to provide CH Turndown

5.6:1

• MAC-115

Modulates input to provide CH Turndown

5.6:1, DHW Turndown 6.9:1

• MAH-125

Modulates input to provide CH Turndown

5.7:1

• MAC-150

Modulates input to provide CH Turndown

5.7:1, DHW Turndown 7:1

• MAH-165

Modulates input to provide CH Turndown

5.5:1

• MAC-205

Modulates input to provide CH Turndown

5.5:1, DHW turndown 7:1

Maximum output available for domestic hot water:

MAC-115

- 105,500 btu/hr (33.8 kW) capable of

providing 2.5 (U.S.) gpm (11.4 liters/min) with a

temperature rise of 70°F/39°C.

MAC-150

- 136,000 btu/h (40 kW), capable of

providing 3.5 (U.S.) gpm (13.2 liters/min) with a

temperature rise of 70°F/39°C.

MAC-205

- 180,000 btu/h (53 kW), capable of

providing 5.0 (U.S.) gpm (18.9 liters/min) with

temperature rise of 70°F/39°C.

•

Integral Low Water Pressure Cutoff.

•  Optional Outdoor Temperature Reset.
•  Heat exchanger over heat protection.
•  Boiler operating at maximum operating temperature,

providing heat, pressure gauge should not indicate

more than 26.11 psi / 1.80 bar. If reading exceeds this

figure larger expansion tank is required.

240013354 REV B [09/15/2021]

2.4 Manufacturer recommends use of Carbon

Monoxide monitor may be requirement of local

jurisdiction.

«
...
9
10
11
12
13
...
»

Summary of Contents for MAC-115












































































































































Reviews:

No comments