UTICA BOILERS BC3095 Installation, Operation & Maintenance Manual Download Page 4

4

Table 2  RATINGS & DATA

Boiler Model 

Number

(1)

AHRI Oil Burner 

Input

(1)

Heating 

Capacity 

MBH

(4)

AHRI Net 

Ratings

(2)(4)

A.F.U.E. 

Rating

Min. Natural Draft 

Chimney Size

G.P.H. MBH

(4)

Water MBH

Round

Square

BC3095

0.95

133

114

99

84.0

6

8x8x15

BC4100

1.00

140

121

105

85.0

6

8x8x15

BC4115

1.15

161

137

119

84.0

6

8x8x15

NOTES:

1. AHRI burner capacity is based on an oil heating value of 140,000 Btu/gal and with 13%  

CO

2

.

2. Net AHRI Water Ratings shown are based on a piping and pickup allowance of 1.15.

3. Consult manufacturer before selecting boiler for installations having unusual piping and 

pickup requirements, such as intermittent system operation, extensive piping.

4. For forced hot water heating systems where boiler and all piping are within the area to 

be heated, select boiler on basis of its Heating Capacity.

5. Nozzle listed for use with Beckett Burner. 

6. Electrical service to be 120 Volts, 15 Amps, & 60 Hz.

STANDARD EQUIPMENT: Crated Boiler, Flush Jacket, 

Oil Burner, Target Wall/Liner, Circulator-1¼", Safety 

Relief Valve, Temperature Pressure Gauge, Drain 

Valve, Wiring Harness, Supply Tapping 1¼", Return 

Tapping 1¼", High Limit and Circulator Control, 

Primary Control.  For Tankless Heater Units-add Low 

Limit. 

Table 3  TANK-LESS WATER HEATER CAPACITIES

Boiler 

Model 

Number

Input 

Rate 

G.P.H.

Tankless 

Heater 

Number

Tankless Heater 

Capacity Intermittent 

Draw G.P.M.

Boiler        

Water 

Content 

(Gallons)

BC3095

0.95

L-24

3.25

6.7

BC4100

1.00

L-24

3.25

8.2

BC4115

1.15

L-24

4.00

8.2

RATINGS, DATA, AND DIMENSIONS

Summary of Contents for BC3095





















Reviews: