UTC RETAIL 3100 Series Installation Manual Download Page 6

Page: 6 / 18

11692017 Rev A

- 6 -

4. Connect the printer USB cable from the printer to any USB port on the rear of the 3100 Series.

5. Connect the power cable from the printer power supply to the connector on the printer. Connect

the AC cable to the printer power supply and then to a wall outlet or the optional Power
Conditioner. Optionally, connect cable 11029567 between the printer and the 24VDC output on
the 3100 Series.

Figure 3:

Rear View of 3100 Series and Printer

6. Connect the mouse and keyboard cables to the 3100 Series. The mouse may be plugged into

any USB port and the keyboard port is purple.

Figure 4:

Rear View of 3100 Series and Top views of keyboard and mouse

You may eliminate the printer’s AC adapter by connecting
cable 11029567 between the 3100 Series 24VDC output
and the printer.

Summary of Contents for 3100 Series



















Search results

Summary of Contents for 3100 Series

Reviews:

Related manuals for 3100 Series

Brands by name

Popular brands

UTC RETAIL 3100 Series, Installation Manual

Search results

Summary of Contents for 3100 Series

Reviews:

Related manuals for 3100 Series

Brands by name

Popular brands