background image

USHIBAYRxxxWPL (300W-480W) Series LED Highbays Installation Guide

MICROWAVE OCCUPANCY DETECTION

& DAYLIGHT HARVESTING SENSOR

NEUTRAL [WHITE]

GROUND [GREEN]

DIM

INPUT

TO LOAD

[LED BOARD]

LINE [BLACK]

WHITE (-) /BLACK(-)

BLUE(+) /GRAY(+)

ACL (BROWN)

ACN (BLUE)

DIM (+) [RED]

DIM (-) [BLACK]

L out [YELLOW]

N [BLUE]

L in [BROWN]

DIM (+) [RED]

DIM (-) [BLACK]

1) Remove the two [2] #4-40 PHMS from the ACHUMO-MB bracket of the ACHUMO 

and remove the small phillips screw from underneath the sensor in order to replace the 

ACHUMO bracket with the ACHUMO3-MB . Using a Phillips screw driver (preferable 

with a magnetic tip), Fasten the bracket onto the FHW luminaire and use the hexnuts 

provided to lock it in place.

2) Remove the ACHUPS sensor from the ACHUPS-MB, and install the sensor to 
the ACHUMO3-MB. Make sure the orientation of the sensor is the same as the 

day harvesting detector.
3) Use the Wire Diagram provided for the required connections. Make sure all wiring 

connections are made inside the J-Box provided and are properly sealed by an 

authorized electrician.

4)  Refer to the Individual installation sheets for the ACHUMO and the ACHUPS for 
adjusting the settings on the Microwave sensor and the  Daylight Harvesting 

Detector. 

PART NO.

IMAGE

DESCRIPTION

QTY

ACHUPS

Photocell/Daylight harvesting Sensor,1-10Vdc Dim 

down/up according to ambient brightness level, 

target light level adjustable. Ip20 rated.

1

ACHUMO

Microwave occupancy sensor with 
J-Box

1

ACHUMO3-MB

Mounting Bracket for the ACHUMO Microwave 

Sensor and ACHUPS Daylight Harvesting Sensor 

to the FHW luminaire.

1

10-00033

#4-40 Pan Head Machine Screw

2

10-00033

#4-40 Hex Nut

2

ACHUMO

ACHUPS

ACHUMO

ACHUPS

AC POWER

SUPPL

Y

DIMMABLE LED DRIVER

FOR INDOOR USE ONLY

CAUTION:

 PLEASE FOLLOW THIS INSTRUCTION MANUAL 

CAREFULLY TO PREVENT ANY INJURIES OR COMPLICATIONS 

THAT MAY ARISE.

WARNING: 

Before installing or maintaining the luminaire, make sure all powers 

are

 TURNED OFF

. Verify that the supply voltage is correct by comparing it with 

the label information on all fixtures. Make all connections in accordance with the 

NEC requirements, and make sure all luminaries are properly secured to prevent 

any wire complications. This luminaire is not to exceed the maximum ambient 

temperature rating noted on the specification sheet.

When ACHUMO microwave sensor works together with the ACHUPS 

daylight harvesting sensor, the lighting fixture will dim the light in response to 

the available daylight in the area when the area is being occupied.

When the customer orders the ACHUMO and the ACHUPS, a special 

mounting bracket will also be included (ACHUMO3-MB). This mounting bracket 

is specifically made to be able to mount both the sensor and occupancy 

detector simultaneously. Each luminaire already comes with two holes made 

specifically for this bracket.

LED INPUT

LED DIM

AC POWER

SUPPLY CORD

ACHUMO

LED DRIVER

INPUT CORD

DRIVER DIM

& ACHUPS

THIS DIAGRAM IS A 

RECOMMENDATION ON HOW TO 

INSTALL THE WIRING INSIDE THE 

JUNCTION BOX.  APPLY WATERPROOF 

SEALANT AFTER ALL WIRING IS 

COMPLETE.

Summary of Contents for USHIBAYR WPL Series









Reviews: